| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| SurrealDB versions before 2.1.0 contain an uncaught exception vulnerability in the rand::time() function that panics when unwrap is called on a None result from timestamp_opt. Authorized clients can repeatedly invoke rand::time() to reliably trigger server panics and cause denial of service. |
| The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled.
As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system.
uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service.
Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running. |
| In Zephyr's Bluetooth Mesh PB-ADV provisioning bearer (subsys/bluetooth/mesh/pb_adv.c), prov_msg_recv() rescheduled the provisioning protocol watchdog timer unconditionally at the top of the function, before the FCS check and before the ADV_LINK_INVALID check. Once a provisioning attempt fails, prov_failed() sets ADV_LINK_INVALID and the only recovery path is the protocol timer firing (protocol_timeout -> prov_link_close -> close_link -> reset_adv_link and re-enabling of scanning and the unprovisioned device beacon).
A remote, unauthenticated attacker on the BLE advertising channel can first induce a provisioning failure (e.g. with a malformed generic-provisioning PDU) and then transmit any FCS-valid PB-ADV transaction PDU on the same link ID more often than once per protocol timeout (60 s, or 120 s for OOB input/output). Because each such packet reset the timer even on an invalidated link, protocol_timeout never fired, the dead link was never torn down, and the device remained pinned in an un-provisionable state with its unprovisioned beacon disabled and new Link Open requests rejected.
PB-ADV PDUs are processed without authentication and the FCS is a keyless CRC, so no pairing or prior trust is required and the attacker chooses the link ID itself. The impact is a persistent denial of provisioning/re-provisioning service; there is no memory-safety, confidentiality, or integrity impact.
The vulnerable code shipped in releases through v4.4.1. The fix moves the timer reschedule to after the ADV_LINK_INVALID check (and the FCS check before the reset) so an invalidated link can no longer be kept alive by incoming packets. |
| The CONFIG_USERSPACE syscall verifier z_vrfy_k_poll() in kernel/poll.c allocates a kernel-side copy of the user-supplied k_poll_event[] via z_thread_malloc() and then validates each event's object handle. Before this fix, validation used K_OOPS(K_SYSCALL_OBJ(...)) inline inside the loop, which kills the calling thread without freeing events_copy.
A user thread can pass num_events >= 1 with a forged object handle to leak the allocation; because newly spawned user threads inherit the parent's resource_pool (kernel/thread.c), an attacker spawns sacrificial threads to repeat the leak until the shared kernel heap is exhausted. Once depleted, legitimate kernel allocations from that pool (k_queue alloc nodes, k_msgq buffers, future k_poll calls, etc.) fail, causing a system-level denial of service.
The fix replaces each inline K_OOPS with a conditional goto oops_free so the buffer is freed before the thread is killed. Affects Zephyr releases from v1.12.0 (when k_poll was first exposed to user mode) through v4.4.1. |
| The MCTP-over-I2C+GPIO target binding in Zephyr (subsys/pmci/mctp/mctp_i2c_gpio_target.c) processes pseudo-register writes from an I2C bus master byte-by-byte in mctp_i2c_gpio_target_write_received() without validating the order or the receive buffer. In the affected versions the MCTP_I2C_GPIO_RX_MSG_ADDR (data) handler dereferences and writes through b->rx_pkt without checking that the receive buffer was allocated: a controller that selects the data register and writes a byte without first sending the length register (which is what allocates the buffer) causes a write of an attacker-chosen byte through a NULL/unallocated mctp_pktbuf pointer (i.e. into a small attacker-advanceable offset above address 0), producing memory corruption or a hard fault.
The same handler also performs a write-then-check bounds test, allowing a one-byte heap overflow at data[255] when more than 255 data bytes are sent.
Because the I2C target callback is invoked with raw bytes supplied by whatever device is the bus master and the binding performs no authentication, a malicious or malfunctioning controller on the bus can trigger these without any prior protocol state, leading to memory corruption and/or denial of service on the target device.
The vulnerable code was introduced when the I2C+GPIO target binding was added and shipped in Zephyr v4.3.0 and v4.4.0. The fix defers allocation to the first data byte with a NULL check, treats a missing length as a zero-sized packet rejected by libmctp, and moves the bounds check before the store. |
| The DesignWare SPI driver (drivers/spi/spi_dw.c) computed the SPI BAUDR clock divider as info->clock_frequency / config->frequency without validating config->frequency.
spi_transceive is a Zephyr __syscall and its verify handler (drivers/spi/spi_handlers.c) copies the caller-supplied spi_config from userspace without checking the frequency field, so a userspace thread that has been granted access to a DesignWare SPI device kernel object can pass frequency = 0 and trigger an unsigned integer divide-by-zero in spi_dw_configure().
On Cortex-M Mainline (SCB->CCR.DIV_0_TRP is set in z_arm_fault_init()) and on ARC (a dedicated __ev_div_zero vector) this raises a CPU exception, resulting in a kernel fault and local denial of service.
The fix rejects zero frequency and frequencies above clock_frequency / 2 (the DesignWare SSI databook minimum SCKDIV of 2) with -EINVAL. The defect affects all Zephyr releases up to and including v4.4.0; exploitation requires CONFIG_USERSPACE=y and an unprivileged thread already granted SPI driver permission. There is no memory-corruption or information-disclosure impact. |
| The Classic (BR/EDR) L2CAP signaling handlers l2cap_br_conf_req() and l2cap_br_conf_rsp() in subsys/bluetooth/host/classic/l2cap_br.c validated the minimum command size against buf->len (the bytes remaining in the whole received PDU) instead of len (the per-command data length from the L2CAP signaling header). Because multiple signaling commands can be packed into one PDU, buf->len may exceed a command's len. An attacker can send a CONF_REQ command with a header length smaller than the configuration-request structure (e.g. 0), followed by another command so that buf->len still satisfies the check. The check then passes incorrectly and opt_len = len - sizeof(*req) underflows the uint16_t to a near-0xFFFF value. The configuration-option loop, which lacks an opt_len-versus-buf->len guard, then walks far past the end of the pooled ACL receive buffer using net_buf pull primitives that perform no runtime bounds check, producing an out-of-bounds read of host memory and, when the out-of-bounds option bytes encode an MTU or flush-timeout option, an out-of-bounds write. The BR/EDR signaling channel is processed before pairing/encryption and an L2CAP channel to an L0 service such as SDP can be opened without pairing, so an unauthenticated peer within radio range that can establish an ACL connection can trigger the flaw, leading to memory corruption and denial of service (host/device crash). The defect is present in released versions including v4.4.0. The fix validates against len instead of buf->len in both handlers. |
| The audit file upload handler does not sanitize filenames, allowing shell metacharacters to flow into system command execution. This input validation failure enables command injection when chained with a related vulnerability. |
| Missing validation of the outer content_type byte on TLS 1.3 encrypted records in s2n-tls allows an active man-in-the-middle to silently discard individual application data records without either endpoint detecting the modification. RFC 8446 Section 5.2 requires that the outer content_type of all encrypted TLS 1.3 records must be application_data (0x17). The s2n-tls AEAD implementation hardcodes this value in the additional authenticated data rather than using the actual wire byte, so the outer content_type is not covered by the authentication tag.
This enables selective suppression of application data. In HTTP pipelining scenarios, dropping a TLS record containing an HTTP request can cause request/response desynchronization, where subsequent responses are delivered to the wrong requests. In write-heavy workloads, a dropped record containing a write request can result in undetectable data loss when the client interprets a subsequent success response as confirmation of the dropped write.
All TLS 1.3 connections are affected. Both TLS clients and servers are affected. TLS 1.2 and QUIC connections are not affected.
We recommend you upgrade s2n-tls to version v1.7.6 |
| The QUIC transport parameters extension handler in s2n-tls incorrectly uses s2n_alloc instead of s2n_realloc to store the peer's transport parameters. When a TLS 1.3 connection goes through a HelloRetryRequest, the handler is called twice on the same connection. On the second call, s2n_alloc zeroes the existing pointer before allocating new memory, causing the first allocation to be leaked.
This can occur during normal QUIC traffic when a client offers a key share group the server does not prefer. An unauthenticated user can amplify the issue by deliberately forcing HelloRetryRequests, causing up to approximately 64 KB of unreachable memory per handshake. Over time, this can lead to increased memory consumption on long-running server processes. The unreachable memory is only reclaimed when the process is restarted.
Only server-side QUIC-enabled deployments are affected. Non-QUIC TLS connections are not affected.
We recommend you upgrade s2n-tls to version v1.7.6 |
| Authorization Bypass Through User-Controlled Key (CWE-639) in Kibana can lead to unauthorized information disclosure and case attachment integrity compromise via Privilege Abuse (CAPEC-122). An inconsistency in Kibana's file access authorization logic allows a low-privileged authenticated user to retrieve, modify, and delete case attachments that belong to feature areas they are not authorized to access. Because the access control check and the resource retrieval use different resolution mechanisms, an authenticated attacker with limited file management permissions can obtain the contents of, modify, or delete protected case attachments — such as those associated with Security Solution cases — without holding the privileges required to access those features. |
| Uncontrolled Resource Consumption (CWE-400) in Elasticsearch can lead to denial of service via Excessive Allocation (CAPEC-130). A user with search privileges can submit a specially crafted search request that causes a data node to exhaust available heap memory, resulting in node unavailability and cluster degradation. An attacker could leverage this vulnerability to cause cluster downtime requiring manual intervention to restore service. |
| Tanium addressed a User Interface (UI) Misrepresentation of Critical Information vulnerability in Tanium Server. |
| Tanium addressed an information disclosure vulnerability in Connect. |
| Uncontrolled Resource Consumption (CWE-400) in Kibana can lead to denial of service via Excessive Allocation (CAPEC-130). An authenticated low-privileged user can exploit an uncontrolled resource consumption vulnerability in Kibana's Canvas functionality by sending a specially crafted request, causing the Kibana server process to terminate and resulting in a denial of service for all users of the affected Kibana instance. |
| Two undocumented privileged accounts exist in Autel Maxi Charger Single firmware through V1.03.51. The accounts use vendor-defined password derivation mechanisms based on device-specific values, allowing an attacker with knowledge of the algorithm and required inputs to authenticate to the web management interface with administrative privileges. |
| Autel Maxi Charger Single firmware through V1.03.51 contains a hard-coded authentication token that bypasses authorization checks for multiple management endpoints. An attacker can supply the special token value to invoke privileged functionality without valid authentication. |
| Reachable Assertion (CWE-617) in Elasticsearch can lead to denial of service via Input Data Manipulation (CAPEC-153). A specially crafted search request containing a null value in a specific query clause causes an internal assertion to be raised during query parsing. Because Elasticsearch treats assertion failures as fatal errors, this terminates the affected node process. A low-privileged authenticated user with read access to at least one index can exploit this condition with a single request to cause a node to terminate, disrupting search availability. In a single-node deployment this fully stops Elasticsearch; in a multi-node cluster it reduces cluster capacity for each affected node. |
| Missing Authorization (CWE-862) in Kibana allows an authenticated user to access and modify Cloud Connect configuration and service settings without the required feature privileges, via direct requests to insufficiently protected product endpoints. |
| Autel Maxi Charger Single firmware through V1.03.51 is vulnerable to OS command injection in the /test endpoint exposed on TCP port 9002. An unauthenticated attacker can supply crafted input in the url parameter to execute arbitrary operating system commands. |
