| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs()
drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions
using plain integer division:
unsigned int width = mode_cmd->width / (i ? info->hsub : 1);
unsigned int height = mode_cmd->height / (i ? info->vsub : 1);
However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses
drm_format_info_plane_width/height() which round up dimensions via
DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object
size check for certain pixel format and dimension combinations.
For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the
GEM size validation path sees height=0 instead of height=1. The
expression (height - 1) then wraps to UINT_MAX as an unsigned int,
causing min_size to overflow and wrap back to a small value. A tiny
GEM object therefore passes the size guard, yet when the GPU accesses
the chroma plane it will read or write memory beyond the object's
bounds.
Fix by replacing the open-coded divisions with drm_format_info_plane_width()
and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match
the calculation already used in framebuffer_check(). |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: fix use-after-free of fmt_src during MBPF check
During concurrency testing, multiple instances can run in parallel, and
each instance uses its own inst->lock while the core->lock protects the
list of active instances. The race happens because these locks cover
different scopes, inst->lock protects only the internals of a single
instance, while the Macro Blocks Per Frame (MBPF) checker walks the
core list under core->lock and reads fields like fmt_src->width and
fmt_src->height. At the same time, iris_close() may free fmt_src and
fmt_dst under inst->lock while the instance is still present in the core
list. This allows a situation where the MBPF checker, still iterating
through the core list, reaches an instance whose fmt_src was already
freed by another thread and ends up dereferencing a dangling pointer,
resulting in a use-after-free. This happens because the MBPF checker
assumes that any instance in the core list is fully valid, but the
freeing of fmt_src and fmt_dst without removing the instance from the
core list is not correct.
The correct ordering is to defer freeing fmt_src and fmt_dst until after
the instance has been removed from the core list and all teardown under
the core lock has completed, ensuring that no dangling pointers are ever
exposed during MBPF checks. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/gem: fix error handling in msm_ioctl_gem_info_get_metadata()
msm_ioctl_gem_info_get_metadata() always returns 0 regardless of
errors. When copy_to_user() fails or the user buffer is too small,
the error code stored in ret is ignored because the function
unconditionally returns 0. This causes userspace to believe the
ioctl succeeded when it did not.
Additionally, kmemdup() can return NULL on allocation failure, but
the return value is not checked. This leads to a NULL pointer
dereference in the subsequent copy_to_user() call.
Add the missing NULL check for kmemdup() and return ret instead of 0.
Note that the SET counterpart (msm_ioctl_gem_info_set_metadata)
correctly returns ret.
Patchwork: https://patchwork.freedesktop.org/patch/714478/ |
| Version 3.0.7 of the Securly Chrome Extension uses deprecated SHA-1 hashing for IWF CSAM URL matching (25,020 hashes) and CIPA blocklist matching (12,352 hashes). |
| Plane is an open-source project management tool. Prior to version 1.3.1, there is a cross-workspace asset authorization bypass lets any authenticated user read, copy, delete, and overwrite assets in other Plane workspaces. This issue has been patched in version 1.3.1. |
| Roxy-WI is a web interface for managing Haproxy, Nginx, Apache and Keepalived servers. In versions 8.2.6.4 and prior, EscapedString (app/modules/roxywi/class_models.py:16-30) is the centralised Pydantic validator used on dozens of fields including SSH credential name, username, description, etc. Its if/elif/elif/else flow returns the metacharacter-stripped value without also enforcing the .. block. An attacker who appends a single ;, &, |, $, or backtick to a .. payload routes the value through the strip arm, where .. survives unblocked and the result is not shlex.quote()'d either. At time of publication, there are no publicly available patches. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: prevent use-after-free when deleting claims
When batadv_bla_del_backbone_claims() removes all claims for a backbone, it
does this by dropping the link entry in the hash list. This list entry
itself was one of the references which need to be dropped at the same time
via batadv_claim_put().
But the batadv_claim_put() must not be done before the last access to the
claim object in this function. Otherwise the claim might be freed already
by the batadv_claim_release() function before the list entry was dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: appletb-kbd: fix UAF in inactivity-timer cleanup path
Commit 38224c472a03 ("HID: appletb-kbd: fix slab use-after-free bug in
appletb_kbd_probe") added timer_delete_sync(&kbd->inactivity_timer) to
both the probe close_hw error path and appletb_kbd_remove(), but the
way it was wired in left the inactivity timer reachable during driver
tear-down via two distinct windows.
Window A -- put_device() before timer_delete_sync():
put_device(&kbd->backlight_dev->dev);
timer_delete_sync(&kbd->inactivity_timer);
The inactivity_timer softirq reads kbd->backlight_dev and calls
backlight_device_set_brightness() -> mutex_lock(&ops_lock). If a
concurrent hid_appletb_bl unbind drops the last devm reference
between these two calls, the backlight_device is freed and the
mutex_lock() touches freed memory.
Window B -- backlight cleanup before hid_hw_stop():
if (kbd->backlight_dev) {
timer_delete_sync(...);
put_device(...);
}
hid_hw_close(hdev);
hid_hw_stop(hdev);
Even after Window A is closed, hid_hw_close()/hid_hw_stop() still run
afterwards, so a late ".event" callback from the HID core (USB URB
completion on real Apple hardware) can arrive after
timer_delete_sync() drained the softirq but before put_device() drops
the reference. That callback reaches reset_inactivity_timer(), which
calls mod_timer() and re-arms the timer. The freshly re-armed timer
can then fire on the about-to-be-freed backlight_device.
Both windows produce the same KASAN slab-use-after-free:
BUG: KASAN: slab-use-after-free in __mutex_lock+0x1aab/0x21c0
Read of size 8 at addr ffff88803ee9a108 by task swapper/0/0
Call Trace:
<IRQ>
__mutex_lock
backlight_device_set_brightness
appletb_inactivity_timer
call_timer_fn
run_timer_softirq
handle_softirqs
Allocated by task N:
devm_backlight_device_register
appletb_bl_probe
Freed by task M:
(concurrent hid_appletb_bl unbind path)
Close both windows at once by reworking the tear-down in
appletb_kbd_remove() and in the probe close_hw error path so that
1) hid_hw_close()/hid_hw_stop() run before the backlight cleanup,
guaranteeing no further .event callback can fire and re-arm the
timer, and
2) inside the "if (kbd->backlight_dev)" block, timer_delete_sync()
runs before put_device(), so the softirq is drained before the
final reference is dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: fix accept queue count leak on transport mismatch
virtio_transport_recv_listen() calls sk_acceptq_added() before
vsock_assign_transport(). If vsock_assign_transport() fails or
selects a different transport, the error path returns without
calling sk_acceptq_removed(), permanently incrementing
sk_ack_backlog.
After approximately backlog+1 such failures, sk_acceptq_is_full()
returns true, causing the listener to reject all new connections.
Fix by moving sk_acceptq_added() to after the transport validation,
matching the pattern used by vmci_transport and hyperv_transport. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Set old handle to NULL before prime swap in change_handle
There was a potential race condition in change_handle. The ioctl
briefly had a single object with two idr entries; a concurrent
gem_close could delete the object and remove one of the handles
while leaving the other one dangling, which could subsequently
be dereferenced for a use-after-free.
To fix this, do the same dance that gem_close itself does.
(f6cd7daecff5 drm: Release driver references to handle before making it available again)
First idr_replace the old handle to NULL. Later, if the prime
operations are successful, actually close it.
create_tail required a similar dance to avoid a similar problem.
(bd46cece51a3 drm/gem: Fix race in drm_gem_handle_create_tail())
It idr_allocs the new handle with NULL, then swaps in the correct
object later to avoid races. We don't need to do that here, since
the only operations that could race are drm_prime, and
change_handle holds the prime lock for the entire duration.
v2: cleanups of error paths |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/hdcp: Add NULL check for media_gt in intel_hdcp_gsc_check_status()
When media GT is disabled via configfs, there is no allocation for
media_gt, which is kept as NULL. In such scenario,
intel_hdcp_gsc_check_status() results in a kernel pagefault error due to
>->uc.gsc being evaluated as an invalid memory address.
Fix that by introducing a NULL check on media_gt and bailing out early
if so.
While at it, also drop the NULL check for gsc, since it can't be NULL if
media_gt is not NULL.
v2:
- Get address for gsc only after checking that gt is not NULL.
(Shuicheng)
- Drop the NULL check for gsc. (Shuicheng)
v3:
- Add "Fixes" and "Cc: <stable...>" tags. (Matt)
(cherry picked from commit bfaf87e84ca3ca3f6e275f9ae56da47a8b55ffd1) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn4: Avoid overflow on msg bound check
As pointed out by SDL, the previous condition may be vulnerable to
overflow.
(cherry picked from commit 3c5367d950140d4ec7af830b2268a5a6fdaa3885) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Add bounds checking to ib_{get,set}_value
The uvd/vce/vcn code accesses the IB at predefined offsets without
checking that the IB is large enough. Check the bounds here. The caller
is responsible for making sure it can handle arbitrary return values.
Also make the idx a uint32_t to prevent overflows causing the condition
to fail. |
| Inappropriate implementation in TabGroups in Google Chrome prior to 149.0.7827.53 allowed a remote attacker to perform UI spoofing via malicious network traffic. (Chromium security severity: Low) |
| Use after free in Extensions in Google Chrome prior to 149.0.7827.53 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: Low) |
| Inappropriate implementation in Enterprise in Google Chrome prior to 149.0.7827.53 allowed a local attacker to perform privilege escalation via physical access to the device. (Chromium security severity: Low) |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: revalidate list cursor after sctp_sendmsg_to_asoc() in SCTP_SENDALL
The SCTP_SENDALL path in sctp_sendmsg() iterates ep->asocs with
list_for_each_entry_safe(), which caches the next entry in @tmp before
the loop body runs. The body calls sctp_sendmsg_to_asoc(), which may
drop the socket lock inside sctp_wait_for_sndbuf().
While the lock is dropped, another thread can SCTP_SOCKOPT_PEELOFF the
association cached in @tmp, migrating it to a new endpoint via
sctp_sock_migrate() (list_del_init() + list_add_tail() to
newep->asocs), and optionally close the new socket which frees the
association via kfree_rcu(). The cached @tmp can also be freed by a
network ABORT for that association, processed in softirq while the
lock is dropped.
sctp_wait_for_sndbuf() revalidates @asoc (the current entry) on re-lock
via the "sk != asoc->base.sk" and "asoc->base.dead" checks, but nothing
revalidates @tmp. After a successful return, the iterator advances to
the stale @tmp, yielding either a use-after-free (if the peeled socket
was closed) or a list-walk onto the new endpoint's list head (type
confusion of &newep->asocs as a struct sctp_association *).
Both are reachable from CapEff=0; the type-confusion path gives
controlled indirect call via the outqueue.sched->init_sid pointer.
Fix by re-deriving @tmp from @asoc after sctp_sendmsg_to_asoc()
returns. @asoc is known to still be on ep->asocs at that point: the
only callers that list_del an association from ep->asocs are
sctp_association_free() (which sets asoc->base.dead) and
sctp_assoc_migrate() (which changes asoc->base.sk), and
sctp_wait_for_sndbuf() checks both under the lock before any
successful return; a tripped check propagates as err < 0 and the loop
bails before the re-derive.
The SCTP_ABORT path in sctp_sendmsg_check_sflags() returns 0 and the
loop hits 'continue' before sctp_sendmsg_to_asoc() is ever called, so
the @tmp cached by list_for_each_entry_safe() still covers the
lock-held free that ba59fb027307 ("sctp: walk the list of asoc
safely") was added for. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: fsl: fix controller deregistration
Make sure to deregister the controller before releasing underlying
resources like DMA during driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: rspi: fix controller deregistration
Make sure to deregister the controller before releasing underlying
resources like DMA during driver unbind. |
| Shenzhen Tenda Technology Co., Ltd Tenda G0 v15.11.0.5 was discovered to contain multiple buffer overflows in the Saveqqlist function via the qqStr and markStr parameters. These vulnerabilities allow attackers to cause a Denial of Service (DoS) via a crafted HTTP request. |
