| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - copy IV using skcipher ivsize
AF_ALG rfc3686-ctr-aes-ccp requests pass an 8-byte IV to the driver.
ccp_aes_complete() restores AES_BLOCK_SIZE bytes into the caller's IV
buffer while RFC3686 skciphers expose an 8-byte IV, so the restore
overruns the provided buffer.
Use crypto_skcipher_ivsize() to copy only the algorithm's IV length. |
| In the Linux kernel, the following vulnerability has been resolved:
pppoe: drop PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the current PPPoE driver assumes an
uncompressed (2-byte) protocol field. However, the generic PPP layer
function ppp_input() is not aware of the negotiation result, and still
accepts PFC frames.
If a peer with a broken implementation or an attacker sends a frame with
a compressed (1-byte) protocol field, the subsequent PPP payload is
shifted by one byte. This causes the network header to be 4-byte
misaligned, which may trigger unaligned access exceptions on some
architectures.
To reduce the attack surface, drop PPPoE PFC frames. Introduce
ppp_skb_is_compressed_proto() helper function to be used in both
ppp_generic.c and pppoe.c to avoid open-coding. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Drop all SCM attributes for SOCKMAP.
SOCKMAP can hide inflight fd from AF_UNIX GC.
When a socket in SOCKMAP receives skb with inflight fd,
sk_psock_verdict_data_ready() looks up the mapped socket and
enqueue skb to its psock->ingress_skb.
Since neither the old nor the new GC can inspect the psock
queue, the hidden skb leaks the inflight sockets. Note that
this cannot be detected via kmemleak because inflight sockets
are linked to a global list.
In addition, SOCKMAP redirect breaks the Tarjan-based GC's
assumption that unix_edge.successor is always alive, which
is no longer true once skb is redirected, resulting in
use-after-free below. [0]
Moreover, SOCKMAP does not call scm_stat_del() properly,
so unix_show_fdinfo() could report an incorrect fd count.
sk_msg_recvmsg() does not support any SCM attributes in the
first place.
Let's drop all SCM attributes before passing skb to the
SOCKMAP layer.
[0]:
BUG: KASAN: slab-use-after-free in unix_del_edges (net/unix/garbage.c:118 net/unix/garbage.c:181 net/unix/garbage.c:251)
Read of size 8 at addr ffff888125362670 by task kworker/56:1/496
CPU: 56 UID: 0 PID: 496 Comm: kworker/56:1 Not tainted 7.0.0-rc7-00263-gb9d8b856689d #3 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
Workqueue: events sk_psock_backlog
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:122)
print_report (mm/kasan/report.c:379)
kasan_report (mm/kasan/report.c:597)
unix_del_edges (net/unix/garbage.c:118 net/unix/garbage.c:181 net/unix/garbage.c:251)
unix_destroy_fpl (net/unix/garbage.c:317)
unix_destruct_scm (./include/net/scm.h:80 ./include/net/scm.h:86 net/unix/af_unix.c:1976)
sk_psock_backlog (./include/linux/skbuff.h:?)
process_scheduled_works (kernel/workqueue.c:?)
worker_thread (kernel/workqueue.c:?)
kthread (kernel/kthread.c:438)
ret_from_fork (arch/x86/kernel/process.c:164)
ret_from_fork_asm (arch/x86/entry/entry_64.S:258)
</TASK>
Allocated by task 955:
kasan_save_track (mm/kasan/common.c:58 mm/kasan/common.c:78)
__kasan_slab_alloc (mm/kasan/common.c:369)
kmem_cache_alloc_noprof (mm/slub.c:4539)
sk_prot_alloc (net/core/sock.c:2240)
sk_alloc (net/core/sock.c:2301)
unix_create1 (net/unix/af_unix.c:1099)
unix_create (net/unix/af_unix.c:1169)
__sock_create (net/socket.c:1606)
__sys_socketpair (net/socket.c:1811)
__x64_sys_socketpair (net/socket.c:1863 net/socket.c:1860 net/socket.c:1860)
do_syscall_64 (arch/x86/entry/syscall_64.c:?)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Freed by task 496:
kasan_save_track (mm/kasan/common.c:58 mm/kasan/common.c:78)
kasan_save_free_info (mm/kasan/generic.c:587)
__kasan_slab_free (mm/kasan/common.c:287)
kmem_cache_free (mm/slub.c:6165)
__sk_destruct (net/core/sock.c:2282 net/core/sock.c:2384)
sk_psock_destroy (./include/net/sock.h:?)
process_scheduled_works (kernel/workqueue.c:?)
worker_thread (kernel/workqueue.c:?)
kthread (kernel/kthread.c:438)
ret_from_fork (arch/x86/kernel/process.c:164)
ret_from_fork_asm (arch/x86/entry/entry_64.S:258) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in smb2_open during durable reconnect
In smb2_open, the call to ksmbd_put_durable_fd(fp) drops the reference
to the durable file descriptor early during the durable reconnect
process. If an error occurs subsequently (eg, ksmbd_iov_pin_rsp fails)
or a scavenger accesses the file, it leads to a use-after-free when
accessing fp properties (eg fp->create_time).
Move the single put to the end of the function below err_out2 so fp
stays valid until smb2_open returns. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: taprio: fix use-after-free in advance_sched() on schedule switch
In advance_sched(), when should_change_schedules() returns true,
switch_schedules() is called to promote the admin schedule to oper.
switch_schedules() queues the old oper schedule for RCU freeing via
call_rcu(), but 'next' still points into an entry of the old oper
schedule. The subsequent 'next->end_time = end_time' and
rcu_assign_pointer(q->current_entry, next) are use-after-free.
Fix this by selecting 'next' from the new oper schedule immediately
after switch_schedules(), and using its pre-calculated end_time.
setup_first_end_time() sets the first entry's end_time to
base_time + interval when the schedule is installed, so the value
is already correct.
The deleted 'end_time = sched_base_time(admin)' assignment was also
harmful independently: it would overwrite the new first entry's
pre-calculated end_time with just base_time. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Bound MIDI endpoint descriptor scans
snd_usbmidi_get_ms_info() validates the internal MIDIStreaming endpoint
descriptor size before using baAssocJackID[], but the descriptor walker can
still return a class-specific endpoint descriptor whose bLength exceeds the
remaining bytes in the endpoint-extra scan.
That leaves later flexible-array reads bounded by bLength, but not by the
remaining bytes in the endpoint-extra scan.
Stop walking when bLength is zero or
extends past the remaining endpoint-extra scan. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/psi: fix race between file release and pressure write
A potential race condition exists between pressure write and cgroup file
release regarding the priv member of struct kernfs_open_file, which
triggers the uaf reported in [1].
Consider the following scenario involving execution on two separate CPUs:
CPU0 CPU1
==== ====
vfs_rmdir()
kernfs_iop_rmdir()
cgroup_rmdir()
cgroup_kn_lock_live()
cgroup_destroy_locked()
cgroup_addrm_files()
cgroup_rm_file()
kernfs_remove_by_name()
kernfs_remove_by_name_ns()
vfs_write() __kernfs_remove()
new_sync_write() kernfs_drain()
kernfs_fop_write_iter() kernfs_drain_open_files()
cgroup_file_write() kernfs_release_file()
pressure_write() cgroup_file_release()
ctx = of->priv;
kfree(ctx);
of->priv = NULL;
cgroup_kn_unlock()
cgroup_kn_lock_live()
cgroup_get(cgrp)
cgroup_kn_unlock()
if (ctx->psi.trigger) // here, trigger uaf for ctx, that is of->priv
The cgroup_rmdir() is protected by the cgroup_mutex, it also safeguards
the memory deallocation of of->priv performed within cgroup_file_release().
However, the operations involving of->priv executed within pressure_write()
are not entirely covered by the protection of cgroup_mutex. Consequently,
if the code in pressure_write(), specifically the section handling the
ctx variable executes after cgroup_file_release() has completed, a uaf
vulnerability involving of->priv is triggered.
Therefore, the issue can be resolved by extending the scope of the
cgroup_mutex lock within pressure_write() to encompass all code paths
involving of->priv, thereby properly synchronizing the race condition
occurring between cgroup_file_release() and pressure_write().
And, if an live kn lock can be successfully acquired while executing
the pressure write operation, it indicates that the cgroup deletion
process has not yet reached its final stage; consequently, the priv
pointer within open_file cannot be NULL. Therefore, the operation to
retrieve the ctx value must be moved to a point *after* the live kn
lock has been successfully acquired.
In another situation, specifically after entering cgroup_kn_lock_live()
but before acquiring cgroup_mutex, there exists a different class of
race condition:
CPU0: write memory.pressure CPU1: write cgroup.pressure=0
=========================== =============================
kernfs_fop_write_iter()
kernfs_get_active_of(of)
pressure_write()
cgroup_kn_lock_live(memory.pressure)
cgroup_tryget(cgrp)
kernfs_break_active_protection(kn)
... blocks on cgroup_mutex
cgroup_pressure_write()
cgroup_kn_lock_live(cgroup.pressure)
cgroup_file_show(memory.pressure, false)
kernfs_show(false)
kernfs_drain_open_files()
cgroup_file_release(of)
kfree(ctx)
of->priv = NULL
cgroup_kn_unlock()
... acquires cgroup_mutex
ctx = of->priv; // may now be NULL
if (ctx->psi.trigger) // NULL dereference
Consequently, there is a possibility that of->priv is NULL, the pressure
write needs to check for this.
Now that the scope of the cgroup_mutex has been expanded, the original
explicit cgroup_get/put operations are no longer necessary, this is
because acquiring/releasing the live kn lock inherently executes a
cgroup get/put operation.
[1]
BUG: KASAN: slab-use-after-free in pressure_write+0xa4/0x210 kernel/cgroup/cgroup.c:4011
Call Trace:
pressure_write+0xa4/0x210 kernel/cgroup/cgroup.c:4011
cgroup_file_write+0x36f/0x790 kernel/cgroup/cgroup.c:43
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix durable fd leak on ClientGUID mismatch in durable v2 open
ksmbd_lookup_fd_cguid() returns a ksmbd_file with its refcount
incremented via ksmbd_fp_get(). parse_durable_handle_context() in
the DURABLE_REQ_V2 case properly releases this reference on every
path inside the ClientGUID-match branch, either by calling
ksmbd_put_durable_fd() or by transferring ownership to dh_info->fp
for a successful reconnect. However, when an entry exists in the
global file table with the same CreateGuid but a different
ClientGUID, the code simply falls through to the new-open path
without dropping the reference obtained from ksmbd_lookup_fd_cguid().
Per MS-SMB2 section 3.3.5.9.10 ("Handling the
SMB2_CREATE_DURABLE_HANDLE_REQUEST_V2 Create Context"), the server
MUST locate an Open whose Open.CreateGuid matches the request's
CreateGuid AND whose Open.ClientGuid matches the ClientGuid of the
connection that received the request. If no such Open is found, the
server MUST continue with the normal open execution phase. A
CreateGuid hit with a ClientGUID mismatch is therefore the
"Open not found" case: proceeding with a new open is correct, but
the reference obtained purely as a side effect of the lookup must
not be leaked.
Repeated requests that hit this mismatch pin global_ft entries,
prevent __ksmbd_close_fd() from ever running for the corresponding
files, and defeat the durable scavenger, leading to long-lived
resource leaks.
Release the reference in the mismatch path and clear dh_info->fp so
subsequent logic does not mistake a non-matching lookup result for
a reconnect target. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_osf: fix potential NULL dereference in ttl check
The nf_osf_ttl() function accessed skb->dev to perform a local interface
address lookup without verifying that the device pointer was valid.
Additionally, the implementation utilized an in_dev_for_each_ifa_rcu
loop to match the packet source address against local interface
addresses. It assumed that packets from the same subnet should not see a
decrement on the initial TTL. A packet might appear it is from the same
subnet but it actually isn't especially in modern environments with
containers and virtual switching.
Remove the device dereference and interface loop. Replace the logic with
a switch statement that evaluates the TTL according to the ttl_check. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: fix BQL imbalance in TX path
Fix a possible BQL imbalance in airoha_dev_xmit(), where inflight
packets are accounted only for the AIROHA_NUM_TX_RING netdev TX
queues. The queue index is computed as:
qid = skb_get_queue_mapping(skb) % ARRAY_SIZE(qdma->q_tx)
txq = netdev_get_tx_queue(dev, qid);
However, airoha_qdma_tx_napi_poll() accounts completions across all
netdev TX queues (num_tx_queues), leading to inconsistent BQL
accounting.
Also reset all netdev TX queues in the ndo_stop callback. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-sysman: bound enumeration string aggregation
populate_enum_data() aggregates firmware-provided value-modifier
and possible-value strings into fixed 512-byte struct members.
The current code bounds each individual source string but then
appends every string and separator with raw strcat() and no
remaining-space check.
Switch the aggregation loops to a bounded append helper and
reject enumeration packages whose combined strings do not fit
in the destination buffers.
[ij: add include] |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Prevent lockup in requeue-PI during signal/ timeout wakeup
During wait-requeue-pi (task A) and requeue-PI (task B) the following
race can happen:
Task A Task B
futex_wait_requeue_pi()
futex_setup_timer()
futex_do_wait()
futex_requeue()
CLASS(hb, hb1)(&key1);
CLASS(hb, hb2)(&key2);
*timeout*
futex_requeue_pi_wakeup_sync()
requeue_state = Q_REQUEUE_PI_IGNORE
*blocks on hb->lock*
futex_proxy_trylock_atomic()
futex_requeue_pi_prepare()
Q_REQUEUE_PI_IGNORE => -EAGAIN
double_unlock_hb(hb1, hb2)
*retry*
Task B acquires both hb locks and attempts to acquire the PI-lock of the
top most waiter (task B). Task A is leaving early due to a signal/
timeout and started removing itself from the queue. It updates its
requeue_state but can not remove it from the list because this requires
the hb lock which is owned by task B.
Usually task A is able to swoop the lock after task B unlocked it.
However if task B is of higher priority then task A may not be able to
wake up in time and acquire the lock before task B gets it again.
Especially on a UP system where A is never scheduled.
As a result task A blocks on the lock and task B busy loops, trying to
make progress but live locks the system instead. Tragic.
This can be fixed by removing the top most waiter from the list in this
case. This allows task B to grab the next top waiter (if any) in the
next iteration and make progress.
Remove the top most waiter if futex_requeue_pi_prepare() fails.
Let the waiter conditionally remove itself from the list in
handle_early_requeue_pi_wakeup(). |
| Jenkins Active Directory Plugin 2.41.1 and earlier does not escape the user name before building the LDAP search filter in the Windows native (ADSI) authentication path, allowing unauthenticated attackers to inject LDAP wildcard characters to enumerate directory entries and to authenticate as a matching user whose password they know without knowing their exact user name. |
| Jenkins Assembla Plugin 1.4 and earlier does not configure its XML parser to prevent XML external entity (XXE) attacks, allowing attackers able to control the responses of the configured Assembla server to extract secrets from the Jenkins controller or perform server-side request forgery. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix potential null-ptr-deref in decode_choose_args()
A message of type CEPH_MSG_OSD_MAP contains an OSD map that itself
contains a CRUSH map. When decoding this CRUSH map in crush_decode(), an
array of max_buckets CRUSH buckets is decoded, where some indices may
not refer to actual buckets and are therefore set to NULL. The received
CRUSH map may optionally contain choose_args that get decoded in
decode_choose_args(). When decoding a crush_choose_arg_map, a series of
choose_args for different buckets is decoded, with the bucket_index
being read from the incoming message. It is only checked that the bucket
index does not exceed max_buckets, but not that it doesn't point to an
index with a NULL bucket. If a (potentially corrupted) message contains
a crush_choose_arg_map including such a bucket_index, a null pointer
dereference may occur in the subsequent processing when attempting to
access the bucket with the given index.
This patch fixes the issue by extending the affected check. Now, it is
only attempted to access the bucket if it is not NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Drop CLONE_THREAD requirement for private default hash alloc
Currently need_futex_hash_allocate_default() depends on strict pthread
semantics, abusing CLONE_THREAD. This breaks the non-concurrency
assumptions when doing the mm->futex_ref pcpu allocations, leading to
bugs[0] when sharing the mm in other ways; ie:
BUG: KASAN: slab-use-after-free in futex_hash_put
... where the +1 bias can end up on a percpu counter that mm->futex_ref
no longer points at.
Loosen the check to cover any CLONE_VM clone, except vfork(). Excluding
vfork keeps the existing paths untouched (no overhead), and we can't
race in the first place: either the parent is suspended and the child
runs alone, or mm->futex_ref is already allocated from an earlier
CLONE_VM. |
| In the Linux kernel, the following vulnerability has been resolved:
net: tls: fix strparser anchor skb leak on offload RX setup failure
When tls_set_device_offload_rx() fails at tls_dev_add(), the error path
calls tls_sw_free_resources_rx() to clean up the SW context that was
initialized by tls_set_sw_offload(). This function calls
tls_sw_release_resources_rx() (which stops the strparser via
tls_strp_stop()) and tls_sw_free_ctx_rx() (which kfrees the context),
but never frees the anchor skb that was allocated by alloc_skb(0) in
tls_strp_init().
Note that tls_sw_free_resources_rx() is exclusively used for this
"failed to start offload" code path, there's no other caller.
The leak did not exist before commit 84c61fe1a75b ("tls: rx: do not use
the standard strparser"), because the standard strparser doesn't try
to pre-allocate an skb.
The normal close path in tls_sk_proto_close() handles cleanup by calling
tls_sw_strparser_done() (which calls tls_strp_done()) after dropping
the socket lock, because tls_strp_done() does cancel_work_sync() and
the strparser work handler takes the socket lock. |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: Balance RCU calls in drbd_adm_dump_devices()
Make drbd_adm_dump_devices() call rcu_read_lock() before
rcu_read_unlock() is called. This has been detected by the Clang
thread-safety analyzer. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix BUG_ON in __ceph_build_xattrs_blob() due to stale blob size
The generic/642 test-case can reproduce the kernel crash:
[40243.605254] ------------[ cut here ]------------
[40243.605956] kernel BUG at fs/ceph/xattr.c:918!
[40243.607142] Oops: invalid opcode: 0000 [#1] SMP PTI
[40243.608067] CPU: 7 UID: 0 PID: 498762 Comm: kworker/7:1 Not tainted 7.0.0-rc7+ #3 PREEMPT(full)
[40243.609700] Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[40243.611820] Workqueue: ceph-msgr ceph_con_workfn
[40243.612715] RIP: 0010:__ceph_build_xattrs_blob+0x1b8/0x1e0
[40243.613731] Code: 0f 84 82 fe ff ff e9 cf 8e 56 ff 48 8d 65 e8 31 c0 5b 41 5c 41 5d 5d 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 c3 cc cc cc cc <0f> 0b 4c 8b 62 08 41 8b 85 24 07 00 00 49 83 c4 04 41 89 44 24 fc
[40243.616888] RSP: 0018:ffffcc80c4d4b688 EFLAGS: 00010287
[40243.617773] RAX: 0000000000010026 RBX: 0000000000000001 RCX: 0000000000000000
[40243.618928] RDX: ffff8a773798dee0 RSI: 0000000000000000 RDI: 0000000000000000
[40243.620158] RBP: ffffcc80c4d4b6a0 R08: 0000000000000000 R09: 0000000000000000
[40243.621573] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a75f3b58000
[40243.622907] R13: ffff8a75f3b58000 R14: 0000000000000080 R15: 000000000000bffd
[40243.624054] FS: 0000000000000000(0000) GS:ffff8a787d1b4000(0000) knlGS:0000000000000000
[40243.625331] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[40243.626269] CR2: 000072f390b623c0 CR3: 000000011c02a003 CR4: 0000000000372ef0
[40243.627408] Call Trace:
[40243.627839] <TASK>
[40243.628188] __prep_cap+0x3fd/0x4a0
[40243.628789] ? do_raw_spin_unlock+0x4e/0xe0
[40243.629474] ceph_check_caps+0x46a/0xc80
[40243.630094] ? __lock_acquire+0x4a2/0x2650
[40243.630773] ? find_held_lock+0x31/0x90
[40243.631347] ? handle_cap_grant+0x79f/0x1060
[40243.632068] ? lock_release+0xd9/0x300
[40243.632696] ? __mutex_unlock_slowpath+0x3e/0x340
[40243.633429] ? lock_release+0xd9/0x300
[40243.634052] handle_cap_grant+0xcf6/0x1060
[40243.634745] ceph_handle_caps+0x122b/0x2110
[40243.635415] mds_dispatch+0x5bd/0x2160
[40243.636034] ? ceph_con_process_message+0x65/0x190
[40243.636828] ? lock_release+0xd9/0x300
[40243.637431] ceph_con_process_message+0x7a/0x190
[40243.638184] ? kfree+0x311/0x4f0
[40243.638749] ? kfree+0x311/0x4f0
[40243.639268] process_message+0x16/0x1a0
[40243.639915] ? sg_free_table+0x39/0x90
[40243.640572] ceph_con_v2_try_read+0xf58/0x2120
[40243.641255] ? lock_acquire+0xc8/0x300
[40243.641863] ceph_con_workfn+0x151/0x820
[40243.642493] process_one_work+0x22f/0x630
[40243.643093] ? process_one_work+0x254/0x630
[40243.643770] worker_thread+0x1e2/0x400
[40243.644332] ? __pfx_worker_thread+0x10/0x10
[40243.645020] kthread+0x109/0x140
[40243.645560] ? __pfx_kthread+0x10/0x10
[40243.646125] ret_from_fork+0x3f8/0x480
[40243.646752] ? __pfx_kthread+0x10/0x10
[40243.647316] ? __pfx_kthread+0x10/0x10
[40243.647919] ret_from_fork_asm+0x1a/0x30
[40243.648556] </TASK>
[40243.648902] Modules linked in: overlay hctr2 libpolyval chacha libchacha adiantum libnh libpoly1305 essiv intel_rapl_msr intel_rapl_common intel_uncore_frequency_common skx_edac_common nfit kvm_intel kvm irqbypass joydev ghash_clmulni_intel aesni_intel rapl input_leds mac_hid psmouse vga16fb serio_raw vgastate floppy i2c_piix4 pata_acpi bochs qemu_fw_cfg i2c_smbus sch_fq_codel rbd dm_crypt msr parport_pc ppdev lp parport efi_pstore
[40243.654766] ---[ end trace 0000000000000000 ]---
Commit d93231a6bc8a ("ceph: prevent a client from exceeding the MDS
maximum xattr size") moved the required_blob_size computation to before
the __build_xattrs() call, introducing a race.
__build_xattrs() releases and reacquires i_ceph_lock during execution.
In that window, handle_cap_grant() may update i_xattrs.blob with a
newer MDS-provided blob and bump i_xattrs.version. When
__bui
---truncated--- |
