Filtered by vendor Cisco
Subscriptions
Filtered by product Nx-os
Subscriptions
Total
276 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2020-3168 | 1 Cisco | 2 Nexus 1000v, Nx-os | 2024-11-21 | 7.5 High |
| A vulnerability in the Secure Login Enhancements capability of Cisco Nexus 1000V Switch for VMware vSphere could allow an unauthenticated, remote attacker to cause an affected Nexus 1000V Virtual Supervisor Module (VSM) to become inaccessible to users through the CLI. The vulnerability is due to improper resource allocation during failed CLI login attempts when login parameters that are part of the Secure Login Enhancements capability are configured on an affected device. An attacker could exploit this vulnerability by performing a high amount of login attempts against the affected device. A successful exploit could cause the affected device to become inaccessible to other users, resulting in a denial of service (DoS) condition requiring a manual power cycle of the VSM to recover. | ||||
| CVE-2020-3165 | 1 Cisco | 65 Nexus 3016, Nexus 3048, Nexus 3064 and 62 more | 2024-11-21 | 8.2 High |
| A vulnerability in the implementation of Border Gateway Protocol (BGP) Message Digest 5 (MD5) authentication in Cisco NX-OS Software could allow an unauthenticated, remote attacker to bypass MD5 authentication and establish a BGP connection with the device. The vulnerability occurs because the BGP MD5 authentication is bypassed if the peer does not have MD5 authentication configured, the NX-OS device does have BGP MD5 authentication configured, and the NX-OS BGP virtual routing and forwarding (VRF) name is configured to be greater than 19 characters. An attacker could exploit this vulnerability by attempting to establish a BGP session with the NX-OS peer. A successful exploit could allow the attacker to establish a BGP session with the NX-OS device without MD5 authentication. The Cisco implementation of the BGP protocol accepts incoming BGP traffic only from explicitly configured peers. To exploit this vulnerability, an attacker must send the malicious packets over a TCP connection that appears to come from a trusted BGP peer. To do so, the attacker must obtain information about the BGP peers in the affected system’s trusted network. | ||||
| CVE-2020-3120 | 1 Cisco | 144 Asr 9000v, Asr 9001, Asr 9006 and 141 more | 2024-11-21 | 6.5 Medium |
| A vulnerability in the Cisco Discovery Protocol implementation for Cisco FXOS Software, Cisco IOS XR Software, and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to a missing check when the affected software processes Cisco Discovery Protocol messages. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected device. A successful exploit could allow the attacker to exhaust system memory, causing the device to reload. Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). | ||||
| CVE-2020-3119 | 1 Cisco | 83 Nexus 3016, Nexus 3048, Nexus 3064 and 80 more | 2024-11-21 | 8.8 High |
| A vulnerability in the Cisco Discovery Protocol implementation for Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to execute arbitrary code or cause a reload on an affected device. The vulnerability exists because the Cisco Discovery Protocol parser does not properly validate input for certain fields in a Cisco Discovery Protocol message. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected device. An successful exploit could allow the attacker to cause a stack overflow, which could allow the attacker to execute arbitrary code with administrative privileges on an affected device. Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). | ||||
| CVE-2020-10136 | 4 Cisco, Digi, Hp and 1 more | 63 Nexus 1000v, Nexus 1000ve, Nexus 3016 and 60 more | 2024-11-21 | 5.3 Medium |
| IP-in-IP protocol specifies IP Encapsulation within IP standard (RFC 2003, STD 1) that decapsulate and route IP-in-IP traffic is vulnerable to spoofing, access-control bypass and other unexpected behavior due to the lack of validation to verify network packets before decapsulation and routing. | ||||
| CVE-2019-1969 | 1 Cisco | 65 Nexus 3016, Nexus 3048, Nexus 3064 and 62 more | 2024-11-21 | 5.3 Medium |
| A vulnerability in the implementation of the Simple Network Management Protocol (SNMP) Access Control List (ACL) feature of Cisco NX-OS Software could allow an unauthenticated, remote attacker to perform SNMP polling of an affected device, even if it is configured to deny SNMP traffic. The vulnerability is due to an incorrect length check when the configured ACL name is the maximum length, which is 32 ASCII characters. An attacker could exploit this vulnerability by performing SNMP polling of an affected device. A successful exploit could allow the attacker to perform SNMP polling that should have been denied. The attacker has no control of the configuration of the SNMP ACL name. | ||||
| CVE-2019-1968 | 1 Cisco | 92 Mds 9000, Mds 9100, Mds 9140 and 89 more | 2024-11-21 | 7.5 High |
| A vulnerability in the NX-API feature of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause an NX-API system process to unexpectedly restart. The vulnerability is due to incorrect validation of the HTTP header of a request that is sent to the NX-API. An attacker could exploit this vulnerability by sending a crafted HTTP request to the NX-API on an affected device. A successful exploit could allow the attacker to cause a denial of service (DoS) condition in the NX-API service; however, the NX-OS device itself would still be available and passing network traffic. Note: The NX-API feature is disabled by default. | ||||
| CVE-2019-1967 | 1 Cisco | 92 Mds 9000, Mds 9100, Mds 9140 and 89 more | 2024-11-21 | 7.5 High |
| A vulnerability in the Network Time Protocol (NTP) feature of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to excessive use of system resources when the affected device is logging a drop action for received MODE_PRIVATE (Mode 7) NTP packets. An attacker could exploit this vulnerability by flooding the device with a steady stream of Mode 7 NTP packets. A successful exploit could allow the attacker to cause high CPU and memory usage on the affected device, which could cause internal system processes to restart or cause the affected device to unexpectedly reload. Note: The NTP feature is enabled by default. | ||||
| CVE-2019-1966 | 1 Cisco | 8 Nx-os, Ucs 6248 Up Fabric Interconnect, Ucs 6296 Up Fabric Interconnect and 5 more | 2024-11-21 | 7.8 High |
| A vulnerability in a specific CLI command within the local management (local-mgmt) context for Cisco UCS Fabric Interconnect Software could allow an authenticated, local attacker to gain elevated privileges as the root user on an affected device. The vulnerability is due to extraneous subcommand options present for a specific CLI command within the local-mgmt context. An attacker could exploit this vulnerability by authenticating to an affected device, entering the local-mgmt context, and issuing a specific CLI command and submitting user input. A successful exploit could allow the attacker to execute arbitrary operating system commands as root on an affected device. The attacker would need to have valid user credentials for the device. | ||||
| CVE-2019-1964 | 1 Cisco | 29 7000 10-slot, 7000 18-slot, 7000 4-slot and 26 more | 2024-11-21 | N/A |
| A vulnerability in the IPv6 traffic processing of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause an unexpected restart of the netstack process on an affected device. The vulnerability is due to improper validation of IPv6 traffic sent through an affected device. An attacker could exploit this vulnerability by sending a malformed IPv6 packet through an affected device. A successful exploit could allow the attacker to cause a denial of service (DoS) condition while the netstack process restarts. A sustained attack could lead to a reboot of the device. | ||||
| CVE-2019-1962 | 1 Cisco | 87 7000 10-slot, 7000 18-slot, 7000 4-slot and 84 more | 2024-11-21 | N/A |
| A vulnerability in the Cisco Fabric Services component of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause process crashes, which can result in a denial of service (DoS) condition on an affected system. The vulnerability is due to insufficient validation of TCP packets when processed by the Cisco Fabric Services over IP (CFSoIP) feature. An attacker could exploit this vulnerability by sending a malicious Cisco Fabric Services TCP packet to an affected device. A successful exploit could allow the attacker to cause process crashes, resulting in a device reload and a DoS condition. Note: There are three distribution methods that can be configured for Cisco Fabric Services. This vulnerability affects only distribution method CFSoIP, which is disabled by default. See the Details section for more information. | ||||
| CVE-2019-1901 | 1 Cisco | 24 Nexus 93108tc-ex, Nexus 93108tc-fx, Nexus 93120tx and 21 more | 2024-11-21 | 8.8 High |
| A vulnerability in the Link Layer Discovery Protocol (LLDP) subsystem of Cisco Nexus 9000 Series Application Centric Infrastructure (ACI) Mode Switch Software could allow an adjacent, unauthenticated attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges. The vulnerability is due to improper input validation of certain type, length, value (TLV) fields of the LLDP frame header. An attacker could exploit this vulnerability by sending a crafted LLDP packet to the targeted device. A successful exploit may lead to a buffer overflow condition that could either cause a DoS condition or allow the attacker to execute arbitrary code with root privileges. Note: This vulnerability cannot be exploited by transit traffic through the device; the crafted packet must be targeted to a directly connected interface. This vulnerability affects Cisco Nexus 9000 Series Fabric Switches in ACI mode if they are running a Cisco Nexus 9000 Series ACI Mode Switch Software release prior to 13.2(7f) or any 14.x release. | ||||
| CVE-2019-1858 | 1 Cisco | 140 7000 10-slot, 7000 18-slot, 7000 4-slot and 137 more | 2024-11-21 | 8.6 High |
| A vulnerability in the Simple Network Management Protocol (SNMP) input packet processor of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause the SNMP application to leak system memory, which could cause an affected device to restart unexpectedly. The vulnerability is due to improper error handling when processing inbound SNMP packets. An attacker could exploit this vulnerability by sending multiple crafted SNMP packets to an affected device. A successful exploit could allow the attacker to cause the SNMP application to leak system memory because of an improperly handled error condition during packet processing. Over time, this memory leak could cause the SNMP application to restart multiple times, leading to a system-level restart and a denial of service (DoS) condition. | ||||
| CVE-2019-1813 | 1 Cisco | 66 9432pq, 9536pq, 9636pq and 63 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the Image Signature Verification feature of Cisco NX-OS Software could allow an authenticated, local attacker with administrator-level credentials to install a malicious software image on an affected device. The vulnerability exists because software digital signatures are not properly verified during CLI command execution. An attacker could exploit this vulnerability to install an unsigned software image on an affected device. | ||||
| CVE-2019-1812 | 1 Cisco | 66 9432pq, 9536pq, 9636pq and 63 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the Image Signature Verification feature of Cisco NX-OS Software could allow an authenticated, local attacker with administrator-level credentials to install a malicious software image on an affected device. The vulnerability exists because software digital signatures are not properly verified during CLI command execution. An attacker could exploit this vulnerability to install an unsigned software image on an affected device. | ||||
| CVE-2019-1811 | 1 Cisco | 66 9432pq, 9536pq, 9636pq and 63 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the Image Signature Verification feature of Cisco NX-OS Software could allow an authenticated, local attacker with administrator-level credentials to install a malicious software image on an affected device. The vulnerability exists because software digital signatures are not properly verified during CLI command execution. An attacker could exploit this vulnerability to install an unsigned software image on an affected device. | ||||
| CVE-2019-1810 | 1 Cisco | 5 N3k-c3164q, N3k-c3232c, N9k-c92304qc and 2 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the Image Signature Verification feature used in an NX-OS CLI command in Cisco Nexus 3000 Series and 9000 Series Switches could allow an authenticated, local attacker with administrator-level credentials to install a malicious software image on an affected device. The vulnerability exists because software digital signatures are not properly verified during CLI command execution. An attacker could exploit this vulnerability to install an unsigned software image on an affected device. Note: If the device has not been patched for the vulnerability previously disclosed in the Cisco Security Advisory cisco-sa-20190306-nxos-sig-verif, a successful exploit could allow the attacker to boot a malicious software image. | ||||
| CVE-2019-1809 | 1 Cisco | 37 7000 10-slot, 7000 18-slot, 7000 4-slot and 34 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the Image Signature Verification feature of Cisco NX-OS Software could allow an authenticated, local attacker with administrator-level credentials to install a malicious software patch on an affected device. The vulnerability is due to improper verification of digital signatures for patch images. An attacker could exploit this vulnerability by crafting an unsigned software patch to bypass signature checks and loading it on an affected device. A successful exploit could allow the attacker to boot a malicious software patch image. | ||||
| CVE-2019-1808 | 1 Cisco | 32 7000 10-slot, 7000 18-slot, 7000 4-slot and 29 more | 2024-11-21 | 4.4 Medium |
| A vulnerability in the Image Signature Verification feature of Cisco NX-OS Software could allow an authenticated, local attacker with administrator-level credentials to install a malicious software patch on an affected device. The vulnerability is due to improper verification of digital signatures for patch images. An attacker could exploit this vulnerability by loading an unsigned software patch on an affected device. A successful exploit could allow the attacker to boot a malicious software patch image. | ||||
| CVE-2019-1795 | 1 Cisco | 144 7000 10-slot, 7000 18-slot, 7000 4-slot and 141 more | 2024-11-21 | 6.7 Medium |
| A vulnerability in the CLI of Cisco FXOS Software and Cisco NX-OS Software could allow an authenticated, local attacker to execute arbitrary commands on the underlying Linux operating system with the privilege level of root. The vulnerability is due to insufficient validation of arguments passed to a specific CLI command on the affected device. An attacker could exploit this vulnerability by including malicious input as the argument of an affected command. A successful exploit could allow the attacker to execute arbitrary commands on the underlying Linux operating system with elevated privileges. An attacker would need valid administrator credentials to exploit this vulnerability. | ||||