| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Avoid __bpf_prog_ret0_warn when jit fails
syzkaller reported an issue:
WARNING: CPU: 3 PID: 217 at kernel/bpf/core.c:2357 __bpf_prog_ret0_warn+0xa/0x20 kernel/bpf/core.c:2357
Modules linked in:
CPU: 3 UID: 0 PID: 217 Comm: kworker/u32:6 Not tainted 6.15.0-rc4-syzkaller-00040-g8bac8898fe39
RIP: 0010:__bpf_prog_ret0_warn+0xa/0x20 kernel/bpf/core.c:2357
Call Trace:
<TASK>
bpf_dispatcher_nop_func include/linux/bpf.h:1316 [inline]
__bpf_prog_run include/linux/filter.h:718 [inline]
bpf_prog_run include/linux/filter.h:725 [inline]
cls_bpf_classify+0x74a/0x1110 net/sched/cls_bpf.c:105
...
When creating bpf program, 'fp->jit_requested' depends on bpf_jit_enable.
This issue is triggered because of CONFIG_BPF_JIT_ALWAYS_ON is not set
and bpf_jit_enable is set to 1, causing the arch to attempt JIT the prog,
but jit failed due to FAULT_INJECTION. As a result, incorrectly
treats the program as valid, when the program runs it calls
`__bpf_prog_ret0_warn` and triggers the WARN_ON_ONCE(1). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Check return value from memblock_phys_alloc_range()
At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of
contiguous free memory available at this point, the kernel will crash
and burn because memblock_phys_alloc_range() returns 0 on failure,
which leads memblock_phys_free() to throw the first 4 MiB of physical
memory to the wolves.
At a minimum it should fail gracefully with a meaningful diagnostic,
but in fact everything seems to work fine without the weird reserve
allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
rseq: Fix segfault on registration when rseq_cs is non-zero
The rseq_cs field is documented as being set to 0 by user-space prior to
registration, however this is not currently enforced by the kernel. This
can result in a segfault on return to user-space if the value stored in
the rseq_cs field doesn't point to a valid struct rseq_cs.
The correct solution to this would be to fail the rseq registration when
the rseq_cs field is non-zero. However, some older versions of glibc
will reuse the rseq area of previous threads without clearing the
rseq_cs field and will also terminate the process if the rseq
registration fails in a secondary thread. This wasn't caught in testing
because in this case the leftover rseq_cs does point to a valid struct
rseq_cs.
What we can do is clear the rseq_cs field on registration when it's
non-zero which will prevent segfaults on registration and won't break
the glibc versions that reuse rseq areas on thread creation. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix unconditional IO throttle caused by REQ_PREFLUSH
When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush()
generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC,
which causes the flush_bio to be throttled by wbt_wait().
An example from v5.4, similar problem also exists in upstream:
crash> bt 2091206
PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0"
#0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8
#1 [ffff800084a2f820] __schedule at ffff800040bfa0c4
#2 [ffff800084a2f880] schedule at ffff800040bfa4b4
#3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4
#4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc
#5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0
#6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254
#7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38
#8 [ffff800084a2fa60] generic_make_request at ffff800040570138
#9 [ffff800084a2fae0] submit_bio at ffff8000405703b4
#10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs]
#11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs]
#12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs]
#13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs]
#14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs]
#15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs]
#16 [ffff800084a2fdb0] process_one_work at ffff800040111d08
#17 [ffff800084a2fe00] worker_thread at ffff8000401121cc
#18 [ffff800084a2fe70] kthread at ffff800040118de4
After commit 2def2845cc33 ("xfs: don't allow log IO to be throttled"),
the metadata submitted by xlog_write_iclog() should not be throttled.
But due to the existence of the dm layer, throttling flush_bio indirectly
causes the metadata bio to be throttled.
Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes
wbt_should_throttle() return false to avoid wbt_wait(). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi: fix MIDI Streaming descriptor lengths
While the MIDI jacks are configured correctly, and the MIDIStreaming
endpoint descriptors are filled with the correct information,
bNumEmbMIDIJack and bLength are set incorrectly in these descriptors.
This does not matter when the numbers of in and out ports are equal, but
when they differ the host will receive broken descriptors with
uninitialized stack memory leaking into the descriptor for whichever
value is smaller.
The precise meaning of "in" and "out" in the port counts is not clearly
defined and can be confusing. But elsewhere the driver consistently
uses this to match the USB meaning of IN and OUT viewed from the host,
so that "in" ports send data to the host and "out" ports receive data
from it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: let net.core.dev_weight always be non-zero
The following problem was encountered during stability test:
(NULL net_device): NAPI poll function process_backlog+0x0/0x530 \
returned 1, exceeding its budget of 0.
------------[ cut here ]------------
list_add double add: new=ffff88905f746f48, prev=ffff88905f746f48, \
next=ffff88905f746e40.
WARNING: CPU: 18 PID: 5462 at lib/list_debug.c:35 \
__list_add_valid_or_report+0xf3/0x130
CPU: 18 UID: 0 PID: 5462 Comm: ping Kdump: loaded Not tainted 6.13.0-rc7+
RIP: 0010:__list_add_valid_or_report+0xf3/0x130
Call Trace:
? __warn+0xcd/0x250
? __list_add_valid_or_report+0xf3/0x130
enqueue_to_backlog+0x923/0x1070
netif_rx_internal+0x92/0x2b0
__netif_rx+0x15/0x170
loopback_xmit+0x2ef/0x450
dev_hard_start_xmit+0x103/0x490
__dev_queue_xmit+0xeac/0x1950
ip_finish_output2+0x6cc/0x1620
ip_output+0x161/0x270
ip_push_pending_frames+0x155/0x1a0
raw_sendmsg+0xe13/0x1550
__sys_sendto+0x3bf/0x4e0
__x64_sys_sendto+0xdc/0x1b0
do_syscall_64+0x5b/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The reproduction command is as follows:
sysctl -w net.core.dev_weight=0
ping 127.0.0.1
This is because when the napi's weight is set to 0, process_backlog() may
return 0 and clear the NAPI_STATE_SCHED bit of napi->state, causing this
napi to be re-polled in net_rx_action() until __do_softirq() times out.
Since the NAPI_STATE_SCHED bit has been cleared, napi_schedule_rps() can
be retriggered in enqueue_to_backlog(), causing this issue.
Making the napi's weight always non-zero solves this problem.
Triggering this issue requires system-wide admin (setting is
not namespaced). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Send signals asynchronously if !preemptible
BPF programs can execute in all kinds of contexts and when a program
running in a non-preemptible context uses the bpf_send_signal() kfunc,
it will cause issues because this kfunc can sleep.
Change `irqs_disabled()` to `!preemptible()`. |
| In the Linux kernel, the following vulnerability has been resolved:
pfifo_tail_enqueue: Drop new packet when sch->limit == 0
Expected behaviour:
In case we reach scheduler's limit, pfifo_tail_enqueue() will drop a
packet in scheduler's queue and decrease scheduler's qlen by one.
Then, pfifo_tail_enqueue() enqueue new packet and increase
scheduler's qlen by one. Finally, pfifo_tail_enqueue() return
`NET_XMIT_CN` status code.
Weird behaviour:
In case we set `sch->limit == 0` and trigger pfifo_tail_enqueue() on a
scheduler that has no packet, the 'drop a packet' step will do nothing.
This means the scheduler's qlen still has value equal 0.
Then, we continue to enqueue new packet and increase scheduler's qlen by
one. In summary, we can leverage pfifo_tail_enqueue() to increase qlen by
one and return `NET_XMIT_CN` status code.
The problem is:
Let's say we have two qdiscs: Qdisc_A and Qdisc_B.
- Qdisc_A's type must have '->graft()' function to create parent/child relationship.
Let's say Qdisc_A's type is `hfsc`. Enqueue packet to this qdisc will trigger `hfsc_enqueue`.
- Qdisc_B's type is pfifo_head_drop. Enqueue packet to this qdisc will trigger `pfifo_tail_enqueue`.
- Qdisc_B is configured to have `sch->limit == 0`.
- Qdisc_A is configured to route the enqueued's packet to Qdisc_B.
Enqueue packet through Qdisc_A will lead to:
- hfsc_enqueue(Qdisc_A) -> pfifo_tail_enqueue(Qdisc_B)
- Qdisc_B->q.qlen += 1
- pfifo_tail_enqueue() return `NET_XMIT_CN`
- hfsc_enqueue() check for `NET_XMIT_SUCCESS` and see `NET_XMIT_CN` => hfsc_enqueue() don't increase qlen of Qdisc_A.
The whole process lead to a situation where Qdisc_A->q.qlen == 0 and Qdisc_B->q.qlen == 1.
Replace 'hfsc' with other type (for example: 'drr') still lead to the same problem.
This violate the design where parent's qlen should equal to the sum of its childrens'qlen.
Bug impact: This issue can be used for user->kernel privilege escalation when it is reachable. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/proc: fix softlockup in __read_vmcore (part 2)
Since commit 5cbcb62dddf5 ("fs/proc: fix softlockup in __read_vmcore") the
number of softlockups in __read_vmcore at kdump time have gone down, but
they still happen sometimes.
In a memory constrained environment like the kdump image, a softlockup is
not just a harmless message, but it can interfere with things like RCU
freeing memory, causing the crashdump to get stuck.
The second loop in __read_vmcore has a lot more opportunities for natural
sleep points, like scheduling out while waiting for a data write to
happen, but apparently that is not always enough.
Add a cond_resched() to the second loop in __read_vmcore to (hopefully)
get rid of the softlockups. |
| In the Linux kernel, the following vulnerability has been resolved:
net_sched: cls_flow: validate TCA_FLOW_RSHIFT attribute
syzbot found that TCA_FLOW_RSHIFT attribute was not validated.
Right shitfing a 32bit integer is undefined for large shift values.
UBSAN: shift-out-of-bounds in net/sched/cls_flow.c:329:23
shift exponent 9445 is too large for 32-bit type 'u32' (aka 'unsigned int')
CPU: 1 UID: 0 PID: 54 Comm: kworker/u8:3 Not tainted 6.13.0-rc3-syzkaller-00180-g4f619d518db9 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:231 [inline]
__ubsan_handle_shift_out_of_bounds+0x3c8/0x420 lib/ubsan.c:468
flow_classify+0x24d5/0x25b0 net/sched/cls_flow.c:329
tc_classify include/net/tc_wrapper.h:197 [inline]
__tcf_classify net/sched/cls_api.c:1771 [inline]
tcf_classify+0x420/0x1160 net/sched/cls_api.c:1867
sfb_classify net/sched/sch_sfb.c:260 [inline]
sfb_enqueue+0x3ad/0x18b0 net/sched/sch_sfb.c:318
dev_qdisc_enqueue+0x4b/0x290 net/core/dev.c:3793
__dev_xmit_skb net/core/dev.c:3889 [inline]
__dev_queue_xmit+0xf0e/0x3f50 net/core/dev.c:4400
dev_queue_xmit include/linux/netdevice.h:3168 [inline]
neigh_hh_output include/net/neighbour.h:523 [inline]
neigh_output include/net/neighbour.h:537 [inline]
ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:236
iptunnel_xmit+0x55d/0x9b0 net/ipv4/ip_tunnel_core.c:82
udp_tunnel_xmit_skb+0x262/0x3b0 net/ipv4/udp_tunnel_core.c:173
geneve_xmit_skb drivers/net/geneve.c:916 [inline]
geneve_xmit+0x21dc/0x2d00 drivers/net/geneve.c:1039
__netdev_start_xmit include/linux/netdevice.h:5002 [inline]
netdev_start_xmit include/linux/netdevice.h:5011 [inline]
xmit_one net/core/dev.c:3590 [inline]
dev_hard_start_xmit+0x27a/0x7d0 net/core/dev.c:3606
__dev_queue_xmit+0x1b73/0x3f50 net/core/dev.c:4434 |
| In the Linux kernel, the following vulnerability has been resolved:
tomoyo: don't emit warning in tomoyo_write_control()
syzbot is reporting too large allocation warning at tomoyo_write_control(),
for one can write a very very long line without new line character. To fix
this warning, I use __GFP_NOWARN rather than checking for KMALLOC_MAX_SIZE,
for practically a valid line should be always shorter than 32KB where the
"too small to fail" memory-allocation rule applies.
One might try to write a valid line that is longer than 32KB, but such
request will likely fail with -ENOMEM. Therefore, I feel that separately
returning -EINVAL when a line is longer than KMALLOC_MAX_SIZE is redundant.
There is no need to distinguish over-32KB and over-KMALLOC_MAX_SIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
safesetid: check size of policy writes
syzbot attempts to write a buffer with a large size to a sysfs entry
with writes handled by handle_policy_update(), triggering a warning
in kmalloc.
Check the size specified for write buffers before allocating.
[PM: subject tweak] |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: Change to kvalloc() in eventlog/acpi.c
The following failure was reported on HPE ProLiant D320:
[ 10.693310][ T1] tpm_tis STM0925:00: 2.0 TPM (device-id 0x3, rev-id 0)
[ 10.848132][ T1] ------------[ cut here ]------------
[ 10.853559][ T1] WARNING: CPU: 59 PID: 1 at mm/page_alloc.c:4727 __alloc_pages_noprof+0x2ca/0x330
[ 10.862827][ T1] Modules linked in:
[ 10.866671][ T1] CPU: 59 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-lp155.2.g52785e2-default #1 openSUSE Tumbleweed (unreleased) 588cd98293a7c9eba9013378d807364c088c9375
[ 10.882741][ T1] Hardware name: HPE ProLiant DL320 Gen12/ProLiant DL320 Gen12, BIOS 1.20 10/28/2024
[ 10.892170][ T1] RIP: 0010:__alloc_pages_noprof+0x2ca/0x330
[ 10.898103][ T1] Code: 24 08 e9 4a fe ff ff e8 34 36 fa ff e9 88 fe ff ff 83 fe 0a 0f 86 b3 fd ff ff 80 3d 01 e7 ce 01 00 75 09 c6 05 f8 e6 ce 01 01 <0f> 0b 45 31 ff e9 e5 fe ff ff f7 c2 00 00 08 00 75 42 89 d9 80 e1
[ 10.917750][ T1] RSP: 0000:ffffb7cf40077980 EFLAGS: 00010246
[ 10.923777][ T1] RAX: 0000000000000000 RBX: 0000000000040cc0 RCX: 0000000000000000
[ 10.931727][ T1] RDX: 0000000000000000 RSI: 000000000000000c RDI: 0000000000040cc0
The above transcript shows that ACPI pointed a 16 MiB buffer for the log
events because RSI maps to the 'order' parameter of __alloc_pages_noprof().
Address the bug by moving from devm_kmalloc() to devm_add_action() and
kvmalloc() and devm_add_action(). |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: Fix assumption that Resolution Multipliers must be in Logical Collections
A report in 2019 by the syzbot fuzzer was found to be connected to two
errors in the HID core associated with Resolution Multipliers. One of
the errors was fixed by commit ea427a222d8b ("HID: core: Fix deadloop
in hid_apply_multiplier."), but the other has not been fixed.
This error arises because hid_apply_multipler() assumes that every
Resolution Multiplier control is contained in a Logical Collection,
i.e., there's no way the routine can ever set multiplier_collection to
NULL. This is in spite of the fact that the function starts with a
big comment saying:
* "The Resolution Multiplier control must be contained in the same
* Logical Collection as the control(s) to which it is to be applied.
...
* If no Logical Collection is
* defined, the Resolution Multiplier is associated with all
* controls in the report."
* HID Usage Table, v1.12, Section 4.3.1, p30
*
* Thus, search from the current collection upwards until we find a
* logical collection...
The comment and the code overlook the possibility that none of the
collections found may be a Logical Collection.
The fix is to set the multiplier_collection pointer to NULL if the
collection found isn't a Logical Collection. |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: fix vlan_get_tci() vs MSG_PEEK
Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found
by syzbot.
Rework vlan_get_tci() to not touch skb at all,
so that it can be used from many cpus on the same skb.
Add a const qualifier to skb argument.
[1]
skbuff: skb_under_panic: text:ffffffff8a8da482 len:32 put:14 head:ffff88807a1d5800 data:ffff88807a1d5810 tail:0x14 end:0x140 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 UID: 0 PID: 5880 Comm: syz-executor172 Not tainted 6.13.0-rc3-syzkaller-00762-g9268abe611b0 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0b 8d 48 c7 c6 9e 6c 26 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 3a 5a 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc90003baf5b8 EFLAGS: 00010286
RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 8565c1eec37aa000
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88802616fb50 R08: ffffffff817f0a4c R09: 1ffff92000775e50
R10: dffffc0000000000 R11: fffff52000775e51 R12: 0000000000000140
R13: ffff88807a1d5800 R14: ffff88807a1d5810 R15: 0000000000000014
FS: 00007fa03261f6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd65753000 CR3: 0000000031720000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
vlan_get_tci+0x272/0x550 net/packet/af_packet.c:565
packet_recvmsg+0x13c9/0x1ef0 net/packet/af_packet.c:3616
sock_recvmsg_nosec net/socket.c:1044 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1066
____sys_recvmsg+0x1c6/0x480 net/socket.c:2814
___sys_recvmsg net/socket.c:2856 [inline]
do_recvmmsg+0x426/0xab0 net/socket.c:2951
__sys_recvmmsg net/socket.c:3025 [inline]
__do_sys_recvmmsg net/socket.c:3048 [inline]
__se_sys_recvmmsg net/socket.c:3041 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3041
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: fix vlan_get_protocol_dgram() vs MSG_PEEK
Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found
by syzbot.
Rework vlan_get_protocol_dgram() to not touch skb at all,
so that it can be used from many cpus on the same skb.
Add a const qualifier to skb argument.
[1]
skbuff: skb_under_panic: text:ffffffff8a8ccd05 len:29 put:14 head:ffff88807fc8e400 data:ffff88807fc8e3f4 tail:0x11 end:0x140 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 5892 Comm: syz-executor883 Not tainted 6.13.0-rc4-syzkaller-00054-gd6ef8b40d075 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0b 8d 48 c7 c6 86 d5 25 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 5a 69 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc900038d7638 EFLAGS: 00010282
RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 609ffd18ea660600
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88802483c8d0 R08: ffffffff817f0a8c R09: 1ffff9200071ae60
R10: dffffc0000000000 R11: fffff5200071ae61 R12: 0000000000000140
R13: ffff88807fc8e400 R14: ffff88807fc8e3f4 R15: 0000000000000011
FS: 00007fbac5e006c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fbac5e00d58 CR3: 000000001238e000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
vlan_get_protocol_dgram+0x165/0x290 net/packet/af_packet.c:585
packet_recvmsg+0x948/0x1ef0 net/packet/af_packet.c:3552
sock_recvmsg_nosec net/socket.c:1033 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1055
____sys_recvmsg+0x1c6/0x480 net/socket.c:2803
___sys_recvmsg net/socket.c:2845 [inline]
do_recvmmsg+0x426/0xab0 net/socket.c:2940
__sys_recvmmsg net/socket.c:3014 [inline]
__do_sys_recvmmsg net/socket.c:3037 [inline]
__se_sys_recvmmsg net/socket.c:3030 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3030
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()
1. The size of the response packet is not validated.
2. The response buffer is not freed.
Resolve these issues by switching to iwl_mvm_send_cmd_status(),
which handles both size validation and frees the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: ip_tunnel: Fix suspicious RCU usage warning in ip_tunnel_init_flow()
There are code paths from which the function is called without holding
the RCU read lock, resulting in a suspicious RCU usage warning [1].
Fix by using l3mdev_master_upper_ifindex_by_index() which will acquire
the RCU read lock before calling
l3mdev_master_upper_ifindex_by_index_rcu().
[1]
WARNING: suspicious RCU usage
6.12.0-rc3-custom-gac8f72681cf2 #141 Not tainted
-----------------------------
net/core/dev.c:876 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/361:
#0: ffffffff86fc7cb0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x377/0xf60
stack backtrace:
CPU: 3 UID: 0 PID: 361 Comm: ip Not tainted 6.12.0-rc3-custom-gac8f72681cf2 #141
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
lockdep_rcu_suspicious.cold+0x4f/0xd6
dev_get_by_index_rcu+0x1d3/0x210
l3mdev_master_upper_ifindex_by_index_rcu+0x2b/0xf0
ip_tunnel_bind_dev+0x72f/0xa00
ip_tunnel_newlink+0x368/0x7a0
ipgre_newlink+0x14c/0x170
__rtnl_newlink+0x1173/0x19c0
rtnl_newlink+0x6c/0xa0
rtnetlink_rcv_msg+0x3cc/0xf60
netlink_rcv_skb+0x171/0x450
netlink_unicast+0x539/0x7f0
netlink_sendmsg+0x8c1/0xd80
____sys_sendmsg+0x8f9/0xc20
___sys_sendmsg+0x197/0x1e0
__sys_sendmsg+0x122/0x1f0
do_syscall_64+0xbb/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_payload: sanitize offset and length before calling skb_checksum()
If access to offset + length is larger than the skbuff length, then
skb_checksum() triggers BUG_ON().
skb_checksum() internally subtracts the length parameter while iterating
over skbuff, BUG_ON(len) at the end of it checks that the expected
length to be included in the checksum calculation is fully consumed. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Add rough attr alloc_size check |
