| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: rds: clear i_sends on setup unwind
The RDS IB connection teardown path is written so it can run during
partial startup and on repeated shutdown attempts. It uses NULL
pointers to distinguish resources that are still owned from resources
that have already been released.
When rds_ib_setup_qp() fails after allocating i_sends but before
allocating i_recvs, the sends_out path frees i_sends without clearing
the pointer. A later shutdown pass can still treat that stale pointer
as a live send ring allocation.
Clear i_sends after vfree() in the error unwind path so the existing
shutdown logic continues to use the correct ownership state. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: errata: Mitigate TLBI errata on various Arm CPUs
A number of CPUs developed by Arm suffer from errata whereby a broadcast
TLBI;DSB sequence may complete before the global observation of writes
which are translated by an affected TLB entry.
These errata ONLY affect the completion of memory accesses which have
been translated by an invalidated TLB entry, and these errata DO NOT
affect the actual invalidation of TLB entries. TLB entries are removed
correctly.
This issue has been assigned CVE ID CVE-2025-10263.
To mitigate this issue, Arm recommends that software follows any
affected TLBI;DSB sequence with an additional TLBI;DSB, which will
ensure that all memory write effects affected by the first TLBI have
been globally observed. The additional TLBI can use any operation that
is broadcast to affected CPUs, and the additional DSB can use any option
that is sufficient to complete the additional TLBI.
The ARM64_WORKAROUND_REPEAT_TLBI workaround is sufficient to mitigate
the issue. Enable this workaround for affected CPUs, and update the
silicon errata documentation accordingly.
Note that due to the manner in which Arm develops IP and tracks errata,
some CPUs share a common erratum number. |
| In the Linux kernel, the following vulnerability has been resolved:
fhandle: fix UAF due to unlocked ->mnt_ns read in may_decode_fh()
may_decode_fh() accesses mount::mnt_ns without holding any locks; that
means the mount can concurrently be unmounted, and the mnt_namespace can
concurrently be freed after an RCU grace period.
This race can happens as follows, assuming that the mount point was
created by open_tree(..., OPEN_TREE_CLONE):
thread 1 thread 2 RCU
__do_sys_open_by_handle_at
do_handle_open
handle_to_path
may_decode_fh
is_mounted
[mount::mnt_ns access]
[mount::mnt_ns access]
__do_sys_close
fput_close_sync
__fput
dissolve_on_fput
umount_tree
class_namespace_excl_destructor
namespace_unlock
free_mnt_ns
mnt_ns_tree_remove
call_rcu(mnt_ns_release_rcu)
mnt_ns_release_rcu
mnt_ns_release
kfree
[mnt_namespace::user_ns access] **UAF**
Fix it by taking rcu_read_lock() around the mount::mnt_ns access, like
in __prepend_path().
Additionally, document the semantics of mount::mnt_ns, and use WRITE_ONCE()
for writers that can race with lockless readers.
This bug is unreachable unless one of the following is set:
- CONFIG_PREEMPTION
- CONFIG_RCU_STRICT_GRACE_PERIOD
because it requires an RCU grace period to happen during a syscall without
an explicit preemption.
This doesn't seem to have interesting security impact; worst-case, it could
leak the result of an integer comparison to userspace (from the level
check in cap_capable()), cause an endless loop, or crash the kernel by
dereferencing an invalid address. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
(cherry picked from commit 37668568641ccc4cc1dbca4923d0a16609dd5707) |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: fix DMA address corruption due to find_vma misuse
fastrpc_get_args() uses find_vma() to look up the VMA for a user-provided
pointer and compute a DMA address offset. When the address falls in a gap
before the returned VMA, (ptr & PAGE_MASK) - vma->vm_start underflows,
corrupting the DMA address sent to the DSP.
Replace find_vma() with vma_lookup(), which returns NULL when the address
is not contained within any VMA. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: clean the sfp upstream if phy probing fails
Sashiko reported that we don't call sfp_bus_del_upstream() in the probe
failure path, so let's add it, otherwise the sfp-bus is left with a
dangling 'upstream' field, that may be used later on during SFP events.
This issue existed before the generic phylib sfp support, back when
drivers were calling phy_sfp_probe themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: check for PCI upstream bridge existence
pci_upstream_bridge() returns NULL if the device is on a root bus. If
8821CE is installed in the system with such a PCI topology, the probing
routine will crash. This has probably been unnoticed as 8821CE is mostly
supplied in laptops where there is a PCI-to-PCI bridge located upstream
from the device. However the card might be installed on a system with
different configuration.
Check if the bridge does exist for the specific workaround to be applied.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/ASPM: Fix link state exit during switch upstream function removal
Before 456d8aa37d0f ("PCI/ASPM: Disable ASPM on MFD function removal to
avoid use-after-free"), we would free the ASPM link only after the last
function on the bus pertaining to the given link was removed.
That was too late. If function 0 is removed before sibling function,
link->downstream would point to free'd memory after.
After above change, we freed the ASPM parent link state upon any function
removal on the bus pertaining to a given link.
That is too early. If the link is to a PCIe switch with MFD on the upstream
port, then removing functions other than 0 first would free a link which
still remains parent_link to the remaining downstream ports.
The resulting GPFs are especially frequent during hot-unplug, because
pciehp removes devices on the link bus in reverse order.
On that switch, function 0 is the virtual P2P bridge to the internal bus.
Free exactly when function 0 is removed -- before the parent link is
obsolete, but after all subordinate links are gone.
[kwilczynski: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: Fix memory leak in hci_le_big_terminate()
hci_le_big_terminate() allocates iso_list_data via kzalloc_obj but
returns 0 without freeing it when neither pa_sync_term nor big_sync_term
flags are set after evaluating the PA and BIG sync connection state.
This early-return path was introduced when hci_le_big_terminate() was
refactored to take struct hci_conn instead of raw u8 parameters, adding
PA/BIG flag evaluation logic. The existing kfree() on hci_cmd_sync_queue
failure does not cover this path. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Set old handle to NULL before prime swap in change_handle
There was a potential race condition in change_handle. The ioctl
briefly had a single object with two idr entries; a concurrent
gem_close could delete the object and remove one of the handles
while leaving the other one dangling, which could subsequently
be dereferenced for a use-after-free.
To fix this, do the same dance that gem_close itself does.
(f6cd7daecff5 drm: Release driver references to handle before making it available again)
First idr_replace the old handle to NULL. Later, if the prime
operations are successful, actually close it.
create_tail required a similar dance to avoid a similar problem.
(bd46cece51a3 drm/gem: Fix race in drm_gem_handle_create_tail())
It idr_allocs the new handle with NULL, then swaps in the correct
object later to avoid races. We don't need to do that here, since
the only operations that could race are drm_prime, and
change_handle holds the prime lock for the entire duration.
v2: cleanups of error paths |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Do not fill_pool() if pi_blocked_on
On RT enabled kernels, fill_pool() ends up calling rtlock_lock(), which
asserts if current::pi_blocked_on is set, because a task can obviously only
block on one lock as otherwise the priority inheritenace chain gets
corrupted.
Prevent this by expanding the conditional to take current::pi_blocked_on
into account. |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't call fill_pool() in early boot hardirq context
When booting a debug PREEMPT_RT kernel on an ARM64 system, a "inconsistent
{HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage" lockdep warning message was
reported to the console.
During early boot, interrupts are enabled before the scheduler is
enabled. In this window (before SYSTEM_SCHEDULING is set) interrupts can
fire and in the hard interrupt context handler attempt to fill the pool
This can lead to a deadlock when the interrupt occurred when the interrupt
hits a region which holds a lock that is required to be taken in the
allocation path.
Add a new can_fill_pool() helper and reorder the exception rule and forbid
this scenario by excluding allocations from hard interrupt context. |
| In the Linux kernel, the following vulnerability has been resolved:
agp/amd64: Fix broken error propagation in agp_amd64_probe()
A NULL pointer dereference was observed in the AMD64 AGP driver when
running in a virtualized environment (e.g. qemu/kvm) without a physical
AMD northbridge. The crash occurs in amd64_fetch_size() when attempting
to dereference the pointer returned by node_to_amd_nb(0).
The root cause of this crash is broken error propagation in
agp_amd64_probe(): When no AMD northbridges are found, cache_nbs()
correctly returns -ENODEV. However, the probe function erroneously
checks the return value against exactly -1, rather than < 0.
As a result, the hardware absence error is masked, allowing the driver
to improperly proceed with initialization. It eventually calls
agp_add_bridge(), which invokes amd64_fetch_size(). Since the hardware
does not exist, node_to_amd_nb(0) returns NULL, leading to a General
Protection Fault (GPF) when accessing its ->misc member.
Fix the issue by correcting the error check in agp_amd64_probe() to
abort properly when cache_nbs() returns any negative error code. This
prevents the driver from erroneously proceeding without hardware, thereby
avoiding the subsequent NULL pointer dereference at its source. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix buffer over-read in rtw_update_protection
rtw_update_protection() is called with a pointer offset into the
ies buffer but the full ie_length is passed, causing a potential
buffer over-read. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix NULL pointer dereference
PCIe errors detected by a Root Port or Downstream Port cause error
recovery services to run on all subordinate devices regardless of
administrative state.
The .error_detected() callback, bnxt_io_error_detected(), disables
and synchronizes IRQs via bnxt_disable_int_sync(), which calls
bnxt_cp_num_to_irq_num() to map completion rings to IRQs using
bp->bnapi.
Since bp->bnapi is allocated on NIC open and freed on NIC close, PCIe
error recovery on a closed NIC can dereference a NULL pointer.
Check if bp->bnapi is NULL before disabling and synchronizing IRQs. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: limit FUSE_NOTIFY_RETRIEVE to uptodate folios
FUSE_NOTIFY_RETRIEVE must be limited to uptodate folios; !uptodate folios
can contain uninitialized data.
Since FUSE_NOTIFY_RETRIEVE is intended to only return data that is already
in the page cache and not wait for data from the FUSE daemon, treat
!uptodate folios as if they weren't present.
This only has security impact on systems that don't enable automatic
zero-initialization of all page allocations via
CONFIG_INIT_ON_ALLOC_DEFAULT_ON or init_on_alloc=1. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: Fix NULL pointer dereference in rpmsg callback
A NULL pointer dereference was observed on Hawi at boot when the DSP
sends a glink message before fastrpc_rpmsg_probe() has completed
initialization:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000178
pc : _raw_spin_lock_irqsave+0x34/0x8c
lr : fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc]
...
Call trace:
_raw_spin_lock_irqsave+0x34/0x8c (P)
fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc]
qcom_glink_native_rx+0x538/0x6a4
qcom_glink_smem_intr+0x14/0x24 [qcom_glink_smem]
The faulting address 0x178 corresponds to the lock variable inside
struct fastrpc_channel_ctx, confirming that cctx is NULL when
fastrpc_rpmsg_callback() attempts to take the spinlock.
There are two issues here. First, dev_set_drvdata() is called before
spin_lock_init() and idr_init(), leaving a window where the callback
can retrieve a valid cctx pointer but operate on an uninitialized
spinlock. Second, the rpmsg channel becomes live as soon as the driver
is bound, so fastrpc_rpmsg_callback() can fire before dev_set_drvdata()
is called at all, resulting in dev_get_drvdata() returning NULL.
Fix both issues by moving all cctx initialization ahead of
dev_set_drvdata() so the structure is fully initialized before it
becomes visible to the callback, and add a NULL check in
fastrpc_rpmsg_callback() as a guard against any remaining window. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phonet: free phonet_device after RCU grace period
phonet_device_destroy() removes a phonet_device from the per-net device
list with list_del_rcu(), but frees it immediately. RCU readers walking
the same list can still hold a pointer to the object after it has been
removed, leading to a slab-use-after-free.
Use kfree_rcu(), matching the lifetime rule already used by
phonet_address_del() for the same object type. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the ACK parser to extract the SACK table for parsing
Fix modification of the received skbuff in rxrpc_input_soft_acks() and a
potential incorrect access of the buffer in a fragmented UDP packet (the
packet would probably have to be deliberately pre-generated as fragmented)
when AF_RXRPC tries to extract the contents of the SACK table by copying
out the contents of the SACK table into a buffer before attempting to parse
AF_RXRPC assumes that it can just call skb_condense() and then validly
access the SACK table from skb->data and that it will be a flat buffer -
but skb_condense() can silently fail to do anything under some
circumstances.
Note that whilst rxrpc_input_soft_acks() should be able to parse extended
ACKs, the rest of AF_RXRPC doesn't currently support that.
Further, there's then no need to call skb_condense() in rxrpc_input_ack(),
so don't. |
