| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
thermal/of: Fix reference leak in thermal_of_cm_lookup()
In thermal_of_cm_lookup(), tr_np is obtained via of_parse_phandle(), but
never released.
Use the __free(device_node) cleanup attribute to automatically release
the node and fix the leak.
[ rjw: Changelog edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
rust: pwm: Fix potential memory leak on init error
When initializing a PWM chip using pwmchip_alloc(), the allocated device
owns an initial reference that must be released on all error paths.
If __pinned_init() were to fail, the allocated pwm_chip would currently
leak because the error path returns without calling pwmchip_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: inside-secure/eip93 - fix kernel panic in driver detach
During driver detach, the same hash algorithm is unregistered multiple
times due to a wrong iterator. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: pm8916_lbc: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
gpib: Fix memory leak in ni_usb_init()
In ni_usb_init(), if ni_usb_setup_init() fails, the function returns
-EFAULT without freeing the allocated writes buffer, leading to a
memory leak.
Additionally, ni_usb_setup_init() returns 0 on failure, which causes
ni_usb_init() to return -EFAULT, an inappropriate error code for this
situation.
Fix the leak by freeing writes in the error path. Modify
ni_usb_setup_init() to return -EINVAL on failure and propagate this
error code in ni_usb_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_infineon: Fix locality leak on get_burstcount() failure
get_burstcount() can return -EBUSY on timeout. When this happens, the
function returns directly without releasing the locality that was
acquired at the beginning of tpm_tis_i2c_send().
Use goto out_err to ensure proper cleanup when get_burstcount() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix inline data read failure for ztailpacking pclusters
Compressed folios for ztailpacking pclusters must be valid before adding
these pclusters to I/O chains. Otherwise, z_erofs_decompress_pcluster()
may assume they are already valid and then trigger a NULL pointer
dereference.
It is somewhat hard to reproduce because the inline data is in the same
block as the tail of the compressed indexes, which are usually read just
before. However, it may still happen if a fatal signal arrives while
read_mapping_folio() is running, as shown below:
erofs: (device dm-1): z_erofs_pcluster_begin: failed to get inline data -4
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
...
pc : z_erofs_decompress_queue+0x4c8/0xa14
lr : z_erofs_decompress_queue+0x160/0xa14
sp : ffffffc08b3eb3a0
x29: ffffffc08b3eb570 x28: ffffffc08b3eb418 x27: 0000000000001000
x26: ffffff8086ebdbb8 x25: ffffff8086ebdbb8 x24: 0000000000000001
x23: 0000000000000008 x22: 00000000fffffffb x21: dead000000000700
x20: 00000000000015e7 x19: ffffff808babb400 x18: ffffffc089edc098
x17: 00000000c006287d x16: 00000000c006287d x15: 0000000000000004
x14: ffffff80ba8f8000 x13: 0000000000000004 x12: 00000006589a77c9
x11: 0000000000000015 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : ffffffffffffffe0 x3 : 0000000000000020
x2 : 0000000000000008 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
z_erofs_decompress_queue+0x4c8/0xa14
z_erofs_runqueue+0x908/0x97c
z_erofs_read_folio+0x128/0x228
filemap_read_folio+0x68/0x128
filemap_get_pages+0x44c/0x8b4
filemap_read+0x12c/0x5b8
generic_file_read_iter+0x4c/0x15c
do_iter_readv_writev+0x188/0x1e0
vfs_iter_read+0xac/0x1a4
backing_file_read_iter+0x170/0x34c
ovl_read_iter+0xf0/0x140
vfs_read+0x28c/0x344
ksys_read+0x80/0xf0
__arm64_sys_read+0x24/0x34
invoke_syscall+0x60/0x114
el0_svc_common+0x88/0xe4
do_el0_svc+0x24/0x30
el0_svc+0x40/0xa8
el0t_64_sync_handler+0x70/0xbc
el0t_64_sync+0x1bc/0x1c0
Fix this by reading the inline data before allocating and adding
the pclusters to the I/O chains. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix memory leak in amdgpu_acpi_enumerate_xcc()
In amdgpu_acpi_enumerate_xcc(), if amdgpu_acpi_dev_init() returns -ENOMEM,
the function returns directly without releasing the allocated xcc_info,
resulting in a memory leak.
Fix this by ensuring that xcc_info is properly freed in the error paths.
Compile tested only. Issue found using a prototype static analysis tool
and code review. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix memory leak in ext4_ext_shift_extents()
In ext4_ext_shift_extents(), if the extent is NULL in the while loop, the
function returns immediately without releasing the path obtained via
ext4_find_extent(), leading to a memory leak.
Fix this by jumping to the out label to ensure the path is properly
released. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: au1200fb: Fix a memory leak in au1200fb_drv_probe()
In au1200fb_drv_probe(), when platform_get_irq fails(), it directly
returns from the function with an error code, which causes a memory
leak.
Replace it with a goto label to ensure proper cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix index out of bounds in degamma hardware format translation
Fixes index out of bounds issue in
`cm_helper_translate_curve_to_degamma_hw_format` function. The issue
could occur when the index 'i' exceeds the number of transfer function
points (TRANSFER_FUNC_POINTS).
The fix adds a check to ensure 'i' is within bounds before accessing the
transfer function points. If 'i' is out of bounds the function returns
false to indicate an error.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:594 cm_helper_translate_curve_to_degamma_hw_format() error: buffer overflow 'output_tf->tf_pts.red' 1025 <= s32max
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:595 cm_helper_translate_curve_to_degamma_hw_format() error: buffer overflow 'output_tf->tf_pts.green' 1025 <= s32max
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:596 cm_helper_translate_curve_to_degamma_hw_format() error: buffer overflow 'output_tf->tf_pts.blue' 1025 <= s32max |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: pxafb: Fix possible use after free in pxafb_task()
In the pxafb_probe function, it calls the pxafb_init_fbinfo function,
after which &fbi->task is associated with pxafb_task. Moreover,
within this pxafb_init_fbinfo function, the pxafb_blank function
within the &pxafb_ops struct is capable of scheduling work.
If we remove the module which will call pxafb_remove to make cleanup,
it will call unregister_framebuffer function which can call
do_unregister_framebuffer to free fbi->fb through
put_fb_info(fb_info), while the work mentioned above will be used.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| pxafb_task
pxafb_remove |
unregister_framebuffer(info) |
do_unregister_framebuffer(fb_info) |
put_fb_info(fb_info) |
// free fbi->fb | set_ctrlr_state(fbi, state)
| __pxafb_lcd_power(fbi, 0)
| fbi->lcd_power(on, &fbi->fb.var)
| //use fbi->fb
Fix it by ensuring that the work is canceled before proceeding
with the cleanup in pxafb_remove.
Note that only root user can remove the driver at runtime. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: drop extent cache when splitting extent fails
When the split extent fails, we might leave some extents still being
processed and return an error directly, which will result in stale
extent entries remaining in the extent status tree. So drop all of the
remaining potentially stale extents if the splitting fails. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix memory access flags in helper prototypes
After commit 37cce22dbd51 ("bpf: verifier: Refactor helper access type tracking"),
the verifier started relying on the access type flags in helper
function prototypes to perform memory access optimizations.
Currently, several helper functions utilizing ARG_PTR_TO_MEM lack the
corresponding MEM_RDONLY or MEM_WRITE flags. This omission causes the
verifier to incorrectly assume that the buffer contents are unchanged
across the helper call. Consequently, the verifier may optimize away
subsequent reads based on this wrong assumption, leading to correctness
issues.
For bpf_get_stack_proto_raw_tp, the original MEM_RDONLY was incorrect
since the helper writes to the buffer. Change it to ARG_PTR_TO_UNINIT_MEM
which correctly indicates write access to potentially uninitialized memory.
Similar issues were recently addressed for specific helpers in commit
ac44dcc788b9 ("bpf: Fix verifier assumptions of bpf_d_path's output buffer")
and commit 2eb7648558a7 ("bpf: Specify access type of bpf_sysctl_get_name args").
Fix these prototypes by adding the correct memory access flags. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: fix ip_rt_bug race in icmp_route_lookup reverse path
icmp_route_lookup() performs multiple route lookups to find a suitable
route for sending ICMP error messages, with special handling for XFRM
(IPsec) policies.
The lookup sequence is:
1. First, lookup output route for ICMP reply (dst = original src)
2. Pass through xfrm_lookup() for policy check
3. If blocked (-EPERM) or dst is not local, enter "reverse path"
4. In reverse path, call xfrm_decode_session_reverse() to get fl4_dec
which reverses the original packet's flow (saddr<->daddr swapped)
5. If fl4_dec.saddr is local (we are the original destination), use
__ip_route_output_key() for output route lookup
6. If fl4_dec.saddr is NOT local (we are a forwarding node), use
ip_route_input() to simulate the reverse packet's input path
7. Finally, pass rt2 through xfrm_lookup() with XFRM_LOOKUP_ICMP flag
The bug occurs in step 6: ip_route_input() is called with fl4_dec.daddr
(original packet's source) as destination. If this address becomes local
between the initial check and ip_route_input() call (e.g., due to
concurrent "ip addr add"), ip_route_input() returns a LOCAL route with
dst.output set to ip_rt_bug.
This route is then used for ICMP output, causing dst_output() to call
ip_rt_bug(), triggering a WARN_ON:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1275 at ip_rt_bug+0x21/0x30, CPU#1
Call Trace:
<TASK>
ip_push_pending_frames+0x202/0x240
icmp_push_reply+0x30d/0x430
__icmp_send+0x1149/0x24f0
ip_options_compile+0xa2/0xd0
ip_rcv_finish_core+0x829/0x1950
ip_rcv+0x2d7/0x420
__netif_receive_skb_one_core+0x185/0x1f0
netif_receive_skb+0x90/0x450
tun_get_user+0x3413/0x3fb0
tun_chr_write_iter+0xe4/0x220
...
Fix this by checking rt2->rt_type after ip_route_input(). If it's
RTN_LOCAL, the route cannot be used for output, so treat it as an error.
The reproducer requires kernel modification to widen the race window,
making it unsuitable as a selftest. It is available at:
https://gist.github.com/mrpre/eae853b72ac6a750f5d45d64ddac1e81 |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: pf1550: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix deadlocks between devlink and netdev instance locks
In the mentioned "Fixes" commit, various work tasks triggering devlink
health reporter recovery were switched to use netdev_trylock to protect
against concurrent tear down of the channels being recovered. But this
had the side effect of introducing potential deadlocks because of
incorrect lock ordering.
The correct lock order is described by the init flow:
probe_one -> mlx5_init_one (acquires devlink lock)
-> mlx5_init_one_devl_locked -> mlx5_register_device
-> mlx5_rescan_drivers_locked -...-> mlx5e_probe -> _mlx5e_probe
-> register_netdev (acquires rtnl lock)
-> register_netdevice (acquires netdev lock)
=> devlink lock -> rtnl lock -> netdev lock.
But in the current recovery flow, the order is wrong:
mlx5e_tx_err_cqe_work (acquires netdev lock)
-> mlx5e_reporter_tx_err_cqe -> mlx5e_health_report
-> devlink_health_report (acquires devlink lock => boom!)
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_recover -> mlx5e_tx_reporter_recover_from_ctx
-> mlx5e_tx_reporter_err_cqe_recover
The same pattern exists in:
mlx5e_reporter_rx_timeout
mlx5e_reporter_tx_ptpsq_unhealthy
mlx5e_reporter_tx_timeout
Fix these by moving the netdev_trylock calls from the work handlers
lower in the call stack, in the respective recovery functions, where
they are actually necessary. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "hwmon: (ibmpex) fix use-after-free in high/low store"
This reverts commit 6946c726c3f4c36f0f049e6f97e88c510b15f65d.
Jean Delvare points out that the patch does not completely
fix the reported problem, that it in fact introduces a
(new) race condition, and that it may actually not be needed in
the first place.
Various AI reviews agree. Specific and relevant AI feedback:
"
This reordering sets the driver data to NULL before removing the sensor
attributes in the loop below.
ibmpex_show_sensor() retrieves this driver data via dev_get_drvdata() but
does not check if it is NULL before dereferencing it to access
data->sensors[].
If a userspace process reads a sensor file (like temp1_input) while this
delete function is running, could it race with the dev_set_drvdata(...,
NULL) call here and crash in ibmpex_show_sensor()?
Would it be safer to keep the original order where device_remove_file() is
called before clearing the driver data? device_remove_file() should wait
for any active sysfs callbacks to complete, which might already prevent the
use-after-free this patch intends to fix.
"
Revert the offending patch. If it can be shown that the originally reported
alleged race condition does indeed exist, it can always be re-introduced
with a complete fix. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: fix panic when IPv4 route references loopback IPv6 nexthop
When a standalone IPv6 nexthop object is created with a loopback device
(e.g., "ip -6 nexthop add id 100 dev lo"), fib6_nh_init() misclassifies
it as a reject route. This is because nexthop objects have no destination
prefix (fc_dst=::), causing fib6_is_reject() to match any loopback
nexthop. The reject path skips fib_nh_common_init(), leaving
nhc_pcpu_rth_output unallocated. If an IPv4 route later references this
nexthop, __mkroute_output() dereferences NULL nhc_pcpu_rth_output and
panics.
Simplify the check in fib6_nh_init() to only match explicit reject
routes (RTF_REJECT) instead of using fib6_is_reject(). The loopback
promotion heuristic in fib6_is_reject() is handled separately by
ip6_route_info_create_nh(). After this change, the three cases behave
as follows:
1. Explicit reject route ("ip -6 route add unreachable 2001:db8::/64"):
RTF_REJECT is set, enters reject path, skips fib_nh_common_init().
No behavior change.
2. Implicit loopback reject route ("ip -6 route add 2001:db8::/32 dev lo"):
RTF_REJECT is not set, takes normal path, fib_nh_common_init() is
called. ip6_route_info_create_nh() still promotes it to reject
afterward. nhc_pcpu_rth_output is allocated but unused, which is
harmless.
3. Standalone nexthop object ("ip -6 nexthop add id 100 dev lo"):
RTF_REJECT is not set, takes normal path, fib_nh_common_init() is
called. nhc_pcpu_rth_output is properly allocated, fixing the crash
when IPv4 routes reference this nexthop. |
