| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tracepoint: balance regfunc() on func_add() failure in tracepoint_add_func()
When a tracepoint goes through the 0 -> 1 transition, tracepoint_add_func()
invokes the subsystem's ext->regfunc() before attempting to install the
new probe via func_add(). If func_add() then fails (for example, when
allocate_probes() cannot allocate a new probe array under memory pressure
and returns -ENOMEM), the function returns the error without calling the
matching ext->unregfunc(), leaving the side effects of regfunc() behind
with no installed probe to justify them.
For syscall tracepoints this is particularly unpleasant: syscall_regfunc()
bumps sys_tracepoint_refcount and sets SYSCALL_TRACEPOINT on every task.
After a leaked failure, the refcount is stuck at a non-zero value with no
consumer, and every task continues paying the syscall trace entry/exit
overhead until reboot. Other subsystems providing regfunc()/unregfunc()
pairs exhibit similarly scoped persistent state.
Mirror the existing 1 -> 0 cleanup and call ext->unregfunc() in the
func_add() error path, gated on the same condition used there so the
unwind is symmetric with the registration. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: mpc52xx: fix controller deregistration
Make sure to deregister the controller before disabling and releasing
underlying resources like interrupts and gpios during driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: cadence-quadspi: fix unclocked access on unbind
Make sure that the controller is runtime resumed before disabling it
during driver unbind to avoid an unclocked register access.
This issue was flagged by Sashiko when reviewing a controller
deregistration fix. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mana: Fix mana_destroy_wq_obj() cleanup in mana_ib_create_qp_rss()
Sashiko points out there are two bugs here in the error unwind flow, both
related to how the WQ table is unwound.
First there is a double i-- on the first failure path due to the while loop
having a i--, remove it.
Second if mana_ib_install_cq_cb() fails then mana_create_wq_obj() is not
undone due to the above i--. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: check for nEPT/nNPT in slow flush hypercalls
Checking is_guest_mode(vcpu) is incorrect, because translate_nested_gpa()
is only valid if an L2 guest is running *with nested EPT/NPT enabled*.
Instead use the same condition as translate_nested_gpa() itself. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: /smack/doi: accept previously used values
Writing to /smack/doi a value that has ever been
written there in the past disables networking for
non-ambient labels.
E.g.
# cat /smack/doi
3
# netlabelctl -p cipso list
Configured CIPSO mappings (1)
DOI value : 3
mapping type : PASS_THROUGH
# netlabelctl -p map list
Configured NetLabel domain mappings (3)
domain: "_" (IPv4)
protocol: UNLABELED
domain: DEFAULT (IPv4)
protocol: CIPSO, DOI = 3
domain: DEFAULT (IPv6)
protocol: UNLABELED
# cat /smack/ambient
_
# cat /proc/$$/attr/smack/current
_
# ping -c1 10.1.95.12
64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.964 ms
# echo foo >/proc/$$/attr/smack/current
# ping -c1 10.1.95.12
64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.956 ms
unknown option 86
# echo 4 >/smack/doi
# echo 3 >/smack/doi
!> [ 214.050395] smk_cipso_doi:691 cipso add rc = -17
# echo 3 >/smack/doi
!> [ 249.402261] smk_cipso_doi:678 remove rc = -2
!> [ 249.402261] smk_cipso_doi:691 cipso add rc = -17
# ping -c1 10.1.95.12
!!> ping: 10.1.95.12: Address family for hostname not supported
# echo _ >/proc/$$/attr/smack/current
# ping -c1 10.1.95.12
64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.617 ms
This happens because Smack keeps decommissioned DOIs,
fails to re-add them, and consequently refuses to add
the “default” domain map:
# netlabelctl -p cipso list
Configured CIPSO mappings (2)
DOI value : 3
mapping type : PASS_THROUGH
DOI value : 4
mapping type : PASS_THROUGH
# netlabelctl -p map list
Configured NetLabel domain mappings (2)
domain: "_" (IPv4)
protocol: UNLABELED
!> (no ipv4 map for default domain here)
domain: DEFAULT (IPv6)
protocol: UNLABELED
Fix by clearing decommissioned DOI definitions and
serializing concurrent DOI updates with a new lock.
Also:
- allow /smack/doi to live unconfigured, since
adding a map (netlbl_cfg_cipsov4_map_add) may fail.
CIPSO_V4_DOI_UNKNOWN(0) indicates the unconfigured DOI
- add new DOI before removing the old default map,
so the old map remains if the add fails
(2008-02-04, Casey Schaufler) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/display/dp_mst: Add protection against 0 vcpi
When releasing a timeslot there is a slight chance we may end up
with the wrong payload mask due to overflow if the delayed_destroy_work
ends up coming into play after a DP 2.1 monitor gets disconnected
which causes vcpi to become 0 then we try to make the payload =
~BIT(vcpi - 1) which is a negative shift. VCPI id should never
really be 0 hence skip changing the payload mask if VCPI is 0.
Otherwise it leads to
<7> [515.287237] xe 0000:03:00.0: [drm:drm_dp_mst_get_port_malloc
[drm_display_helper]] port ffff888126ce9000 (3)
<4> [515.287267] -----------[ cut here ]-----------
<3> [515.287268] UBSAN: shift-out-of-bounds in
../drivers/gpu/drm/display/drm_dp_mst_topology.c:4575:36
<3> [515.287271] shift exponent -1 is negative
<4> [515.287275] CPU: 7 UID: 0 PID: 3108 Comm: kworker/u64:33 Tainted: G
S U 6.17.0-rc6-lgci-xe-xe-3795-3e79699fa1b216e92+ #1 PREEMPT(voluntary)
<4> [515.287279] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
<4> [515.287279] Hardware name: ASUS System Product Name/PRIME Z790-P
WIFI, BIOS 1645 03/15/2024
<4> [515.287281] Workqueue: drm_dp_mst_wq drm_dp_delayed_destroy_work
[drm_display_helper]
<4> [515.287303] Call Trace:
<4> [515.287304] <TASK>
<4> [515.287306] dump_stack_lvl+0xc1/0xf0
<4> [515.287313] dump_stack+0x10/0x20
<4> [515.287316] __ubsan_handle_shift_out_of_bounds+0x133/0x2e0
<4> [515.287324] ? drm_atomic_get_private_obj_state+0x186/0x1d0
<4> [515.287333] drm_dp_atomic_release_time_slots.cold+0x17/0x3d
[drm_display_helper]
<4> [515.287355] mst_connector_atomic_check+0x159/0x180 [xe]
<4> [515.287546] drm_atomic_helper_check_modeset+0x4d9/0xfa0
<4> [515.287550] ? __ww_mutex_lock.constprop.0+0x6f/0x1a60
<4> [515.287562] intel_atomic_check+0x119/0x2b80 [xe]
<4> [515.287740] ? find_held_lock+0x31/0x90
<4> [515.287747] ? lock_release+0xce/0x2a0
<4> [515.287754] drm_atomic_check_only+0x6a2/0xb40
<4> [515.287758] ? drm_atomic_add_affected_connectors+0x12b/0x140
<4> [515.287765] drm_atomic_commit+0x6e/0xf0
<4> [515.287766] ? _pfx__drm_printfn_info+0x10/0x10
<4> [515.287774] drm_client_modeset_commit_atomic+0x25c/0x2b0
<4> [515.287794] drm_client_modeset_commit_locked+0x60/0x1b0
<4> [515.287795] ? mutex_lock_nested+0x1b/0x30
<4> [515.287801] drm_client_modeset_commit+0x26/0x50
<4> [515.287804] __drm_fb_helper_restore_fbdev_mode_unlocked+0xdc/0x110
<4> [515.287810] drm_fb_helper_hotplug_event+0x120/0x140
<4> [515.287814] drm_fbdev_client_hotplug+0x28/0xd0
<4> [515.287819] drm_client_hotplug+0x6c/0xf0
<4> [515.287824] drm_client_dev_hotplug+0x9e/0xd0
<4> [515.287829] drm_kms_helper_hotplug_event+0x1a/0x30
<4> [515.287834] drm_dp_delayed_destroy_work+0x3df/0x410
[drm_display_helper]
<4> [515.287861] process_one_work+0x22b/0x6f0
<4> [515.287874] worker_thread+0x1e8/0x3d0
<4> [515.287879] ? __pfx_worker_thread+0x10/0x10
<4> [515.287882] kthread+0x11c/0x250
<4> [515.287886] ? __pfx_kthread+0x10/0x10
<4> [515.287890] ret_from_fork+0x2d7/0x310
<4> [515.287894] ? __pfx_kthread+0x10/0x10
<4> [515.287897] ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: Fix NULL pointer dereference on panthor_fw_unplug
This patch removes the MCU halt and wait for halt procedures during
panthor_fw_unplug() as the MCU can be in a variety of states or the FW
may not even be loaded/initialized at all, the latter of which can lead
to a NULL pointer dereference.
It should be safe on unplug to just disable the MCU without waiting for
it to halt as it may not be able to. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Initialize new folios before use
KMSAN reports an uninitialized value in longest_match_std(), invoked
from ntfs_compress_write(). When new folios are allocated without being
marked uptodate and ni_read_frame() is skipped because the caller expects
the frame to be completely overwritten, some reserved folios may remain
only partially filled, leaving the rest memory uninitialized. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: fix ntfs_mount_options leak in ntfs_fill_super()
In ntfs_fill_super(), the fc->fs_private pointer is set to NULL without
first freeing the memory it points to. This causes the subsequent call to
ntfs_fs_free() to skip freeing the ntfs_mount_options structure.
This results in a kmemleak report:
unreferenced object 0xff1100015378b800 (size 32):
comm "mount", pid 582, jiffies 4294890685
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 ed ff ed ff 00 04 00 00 ................
backtrace (crc ed541d8c):
__kmalloc_cache_noprof+0x424/0x5a0
__ntfs_init_fs_context+0x47/0x590
alloc_fs_context+0x5d8/0x960
__x64_sys_fsopen+0xb1/0x190
do_syscall_64+0x50/0x1f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This issue can be reproduced using the following commands:
fallocate -l 100M test.file
mount test.file /tmp/test
Since sbi->options is duplicated from fc->fs_private and does not
directly use the memory allocated for fs_private, it is unnecessary to
set fc->fs_private to NULL.
Additionally, this patch simplifies the code by utilizing the helper
function put_mount_options() instead of open-coding the cleanup logic. |
| In the Linux kernel 5.0.21, mounting a crafted btrfs filesystem image can lead to slab-out-of-bounds write access in index_rbio_pages in fs/btrfs/raid56.c. |
| In xsltCopyText in transform.c in libxslt 1.1.33, a pointer variable isn't reset under certain circumstances. If the relevant memory area happened to be freed and reused in a certain way, a bounds check could fail and memory outside a buffer could be written to, or uninitialized data could be disclosed. |
| drivers/gpu/drm/radeon/radeon_display.c in the Linux kernel 5.2.14 does not check the alloc_workqueue return value, leading to a NULL pointer dereference. NOTE: A third-party software maintainer states that the work queue allocation is happening during device initialization, which for a graphics card occurs during boot. It is not attacker controllable and OOM at that time is highly unlikely |
| An issue was discovered in the Linux kernel before 5.2.3. There is a use-after-free caused by a malicious USB device in the drivers/media/usb/dvb-usb/dvb-usb-init.c driver. |
| ICMP information such as (1) netmask and (2) timestamp is allowed from arbitrary hosts. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: microchip-core-qspi: don't attempt to transmit during emulated read-only dual/quad operations
The core will deal with reads by creating clock cycles itself, there's
no need to generate clock cycles by transmitting garbage data at the
driver level. Further, transmitting garbage data just bricks the transfer
since QSPI doesn't have a dedicated master-out line like MOSI in regular
SPI. I'm not entirely sure if the transfer is bricked because of the
garbage data being transmitted on the bus or because the core loses
track of whether it is supposed to be sending or receiving data. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix bpf_xdp_store_bytes proto for read-only arg
While making some maps in Cilium read-only from the BPF side, we noticed
that the bpf_xdp_store_bytes proto is incorrect. In particular, the
verifier was throwing the following error:
; ret = ctx_store_bytes(ctx, l3_off + offsetof(struct iphdr, saddr),
&nat->address, 4, 0);
635: (79) r1 = *(u64 *)(r10 -144) ; R1=ctx() R10=fp0 fp-144=ctx()
636: (b4) w2 = 26 ; R2=26
637: (b4) w4 = 4 ; R4=4
638: (b4) w5 = 0 ; R5=0
639: (85) call bpf_xdp_store_bytes#190
write into map forbidden, value_size=6 off=0 size=4
nat comes from a BPF_F_RDONLY_PROG map, so R3 is a PTR_TO_MAP_VALUE.
The verifier checks the helper's memory access to R3 in
check_mem_size_reg, as it reaches ARG_CONST_SIZE argument. The third
argument has expected type ARG_PTR_TO_UNINIT_MEM, which includes the
MEM_WRITE flag. The verifier thus checks for a BPF_WRITE access on R3.
Given R3 points to a read-only map, the check fails.
Conversely, ARG_PTR_TO_UNINIT_MEM can also lead to the helper reading
from uninitialized memory.
This patch simply fixes the expected argument type to match that of
bpf_skb_store_bytes. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: fix role switching during resume
If the role change while we are suspended, the cdns3 driver switches to the
new mode during resume. However, switching to host mode in this context
causes a NULL pointer dereference.
The host role's start() operation registers a xhci-hcd device, but its
probe is deferred while we are in the resume path. The host role's resume()
operation assumes the xhci-hcd device is already probed, which is not the
case, leading to the dereference. Since the start() operation of the new
role is already called, the resume operation can be skipped.
So skip the resume operation for the new role if a role switch occurs
during resume. Once the resume sequence is complete, the xhci-hcd device
can be probed in case of host mode.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000208
Mem abort info:
...
Data abort info:
...
[0000000000000208] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
Modules linked in:
CPU: 0 UID: 0 PID: 146 Comm: sh Not tainted
6.19.0-rc7-00013-g6e64f4aabfae-dirty #135 PREEMPT
Hardware name: Texas Instruments J7200 EVM (DT)
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : usb_hcd_is_primary_hcd+0x0/0x1c
lr : cdns_host_resume+0x24/0x5c
...
Call trace:
usb_hcd_is_primary_hcd+0x0/0x1c (P)
cdns_resume+0x6c/0xbc
cdns3_controller_resume.isra.0+0xe8/0x17c
cdns3_plat_resume+0x18/0x24
platform_pm_resume+0x2c/0x68
dpm_run_callback+0x90/0x248
device_resume+0x100/0x24c
dpm_resume+0x190/0x2ec
dpm_resume_end+0x18/0x34
suspend_devices_and_enter+0x2b0/0xa44
pm_suspend+0x16c/0x5fc
state_store+0x80/0xec
kobj_attr_store+0x18/0x2c
sysfs_kf_write+0x7c/0x94
kernfs_fop_write_iter+0x130/0x1dc
vfs_write+0x240/0x370
ksys_write+0x70/0x108
__arm64_sys_write+0x1c/0x28
invoke_syscall+0x48/0x10c
el0_svc_common.constprop.0+0x40/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x34/0x108
el0t_64_sync_handler+0xa0/0xe4
el0t_64_sync+0x198/0x19c
Code: 52800003 f9407ca5 d63f00a0 17ffffe4 (f9410401)
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: remove WARN_ON_ONCE when accessing forward path array
Although unlikely, recent support for IPIP tunnels increases chances of
reaching this WARN_ON_ONCE if userspace manages to build a sufficiently
long forward path.
Remove it. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: fix IO hang with degraded array with llbitmap
When llbitmap bit state is still unwritten, any new write should force
rcw, as bitmap_ops->blocks_synced() is checked in handle_stripe_dirtying().
However, later the same check is missing in need_this_block(), causing
stripe to deadloop during handling because handle_stripe() will decide
to go to handle_stripe_fill(), meanwhile need_this_block() always return
0 and nothing is handled. |
