| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: make wait_context part of q_info
Make the wait_context a full part of the q_info struct rather
than a stack variable that goes away after pdsc_adminq_post()
is done so that the context is still available after the wait
loop has given up.
There was a case where a slow development firmware caused
the adminq request to time out, but then later the FW finally
finished the request and sent the interrupt. The handler tried
to complete_all() the completion context that had been created
on the stack in pdsc_adminq_post() but no longer existed.
This caused bad pointer usage, kernel crashes, and much wailing
and gnashing of teeth. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Reset IRTE to host control if *new* route isn't postable
Restore an IRTE back to host control (remapped or posted MSI mode) if the
*new* GSI route prevents posting the IRQ directly to a vCPU, regardless of
the GSI routing type. Updating the IRTE if and only if the new GSI is an
MSI results in KVM leaving an IRTE posting to a vCPU.
The dangling IRTE can result in interrupts being incorrectly delivered to
the guest, and in the worst case scenario can result in use-after-free,
e.g. if the VM is torn down, but the underlying host IRQ isn't freed. |
| In the Linux kernel, the following vulnerability has been resolved:
9p/net: fix improper handling of bogus negative read/write replies
In p9_client_write() and p9_client_read_once(), if the server
incorrectly replies with success but a negative write/read count then we
would consider written (negative) <= rsize (positive) because both
variables were signed.
Make variables unsigned to avoid this problem.
The reproducer linked below now fails with the following error instead
of a null pointer deref:
9pnet: bogus RWRITE count (4294967295 > 3) |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Only create /proc/fs/netfs with CONFIG_PROC_FS
When testing a special config:
CONFIG_NETFS_SUPPORTS=y
CONFIG_PROC_FS=n
The system crashes with something like:
[ 3.766197] ------------[ cut here ]------------
[ 3.766484] kernel BUG at mm/mempool.c:560!
[ 3.766789] Oops: invalid opcode: 0000 [#1] SMP NOPTI
[ 3.767123] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W
[ 3.767777] Tainted: [W]=WARN
[ 3.767968] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
[ 3.768523] RIP: 0010:mempool_alloc_slab.cold+0x17/0x19
[ 3.768847] Code: 50 fe ff 58 5b 5d 41 5c 41 5d 41 5e 41 5f e9 93 95 13 00
[ 3.769977] RSP: 0018:ffffc90000013998 EFLAGS: 00010286
[ 3.770315] RAX: 000000000000002f RBX: ffff888100ba8640 RCX: 0000000000000000
[ 3.770749] RDX: 0000000000000000 RSI: 0000000000000003 RDI: 00000000ffffffff
[ 3.771217] RBP: 0000000000092880 R08: 0000000000000000 R09: ffffc90000013828
[ 3.771664] R10: 0000000000000001 R11: 00000000ffffffea R12: 0000000000092cc0
[ 3.772117] R13: 0000000000000400 R14: ffff8881004b1620 R15: ffffea0004ef7e40
[ 3.772554] FS: 0000000000000000(0000) GS:ffff8881b5f3c000(0000) knlGS:0000000000000000
[ 3.773061] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3.773443] CR2: ffffffff830901b4 CR3: 0000000004296001 CR4: 0000000000770ef0
[ 3.773884] PKRU: 55555554
[ 3.774058] Call Trace:
[ 3.774232] <TASK>
[ 3.774371] mempool_alloc_noprof+0x6a/0x190
[ 3.774649] ? _printk+0x57/0x80
[ 3.774862] netfs_alloc_request+0x85/0x2ce
[ 3.775147] netfs_readahead+0x28/0x170
[ 3.775395] read_pages+0x6c/0x350
[ 3.775623] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.775928] page_cache_ra_unbounded+0x1bd/0x2a0
[ 3.776247] filemap_get_pages+0x139/0x970
[ 3.776510] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.776820] filemap_read+0xf9/0x580
[ 3.777054] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.777368] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.777674] ? find_held_lock+0x32/0x90
[ 3.777929] ? netfs_start_io_read+0x19/0x70
[ 3.778221] ? netfs_start_io_read+0x19/0x70
[ 3.778489] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.778800] ? lock_acquired+0x1e6/0x450
[ 3.779054] ? srso_alias_return_thunk+0x5/0xfbef5
[ 3.779379] netfs_buffered_read_iter+0x57/0x80
[ 3.779670] __kernel_read+0x158/0x2c0
[ 3.779927] bprm_execve+0x300/0x7a0
[ 3.780185] kernel_execve+0x10c/0x140
[ 3.780423] ? __pfx_kernel_init+0x10/0x10
[ 3.780690] kernel_init+0xd5/0x150
[ 3.780910] ret_from_fork+0x2d/0x50
[ 3.781156] ? __pfx_kernel_init+0x10/0x10
[ 3.781414] ret_from_fork_asm+0x1a/0x30
[ 3.781677] </TASK>
[ 3.781823] Modules linked in:
[ 3.782065] ---[ end trace 0000000000000000 ]---
This is caused by the following error path in netfs_init():
if (!proc_mkdir("fs/netfs", NULL))
goto error_proc;
Fix this by adding ifdef in netfs_main(), so that /proc/fs/netfs is only
created with CONFIG_PROC_FS. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: bnxt: fix missing ring index trim on error path
Commit under Fixes converted tx_prod to be free running but missed
masking it on the Tx error path. This crashes on error conditions,
for example when DMA mapping fails. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: decrease sc_count directly if fail to queue dl_recall
A deadlock warning occurred when invoking nfs4_put_stid following a failed
dl_recall queue operation:
T1 T2
nfs4_laundromat
nfs4_get_client_reaplist
nfs4_anylock_blockers
__break_lease
spin_lock // ctx->flc_lock
spin_lock // clp->cl_lock
nfs4_lockowner_has_blockers
locks_owner_has_blockers
spin_lock // flctx->flc_lock
nfsd_break_deleg_cb
nfsd_break_one_deleg
nfs4_put_stid
refcount_dec_and_lock
spin_lock // clp->cl_lock
When a file is opened, an nfs4_delegation is allocated with sc_count
initialized to 1, and the file_lease holds a reference to the delegation.
The file_lease is then associated with the file through kernel_setlease.
The disassociation is performed in nfsd4_delegreturn via the following
call chain:
nfsd4_delegreturn --> destroy_delegation --> destroy_unhashed_deleg -->
nfs4_unlock_deleg_lease --> kernel_setlease --> generic_delete_lease
The corresponding sc_count reference will be released after this
disassociation.
Since nfsd_break_one_deleg executes while holding the flc_lock, the
disassociation process becomes blocked when attempting to acquire flc_lock
in generic_delete_lease. This means:
1) sc_count in nfsd_break_one_deleg will not be decremented to 0;
2) The nfs4_put_stid called by nfsd_break_one_deleg will not attempt to
acquire cl_lock;
3) Consequently, no deadlock condition is created.
Given that sc_count in nfsd_break_one_deleg remains non-zero, we can
safely perform refcount_dec on sc_count directly. This approach
effectively avoids triggering deadlock warnings. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: harden block_group::bg_list against list_del() races
As far as I can tell, these calls of list_del_init() on bg_list cannot
run concurrently with btrfs_mark_bg_unused() or btrfs_mark_bg_to_reclaim(),
as they are in transaction error paths and situations where the block
group is readonly.
However, if there is any chance at all of racing with mark_bg_unused(),
or a different future user of bg_list, better to be safe than sorry.
Otherwise we risk the following interleaving (bg_list refcount in parens)
T1 (some random op) T2 (btrfs_mark_bg_unused)
!list_empty(&bg->bg_list); (1)
list_del_init(&bg->bg_list); (1)
list_move_tail (1)
btrfs_put_block_group (0)
btrfs_delete_unused_bgs
bg = list_first_entry
list_del_init(&bg->bg_list);
btrfs_put_block_group(bg); (-1)
Ultimately, this results in a broken ref count that hits zero one deref
early and the real final deref underflows the refcount, resulting in a WARNING. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Tear down vGIC on failed vCPU creation
If kvm_arch_vcpu_create() fails to share the vCPU page with the
hypervisor, we propagate the error back to the ioctl but leave the
vGIC vCPU data initialised. Note only does this leak the corresponding
memory when the vCPU is destroyed but it can also lead to use-after-free
if the redistributor device handling tries to walk into the vCPU.
Add the missing cleanup to kvm_arch_vcpu_create(), ensuring that the
vGIC vCPU structures are destroyed on error. |
| In the Linux kernel, the following vulnerability has been resolved:
xen-netfront: handle NULL returned by xdp_convert_buff_to_frame()
The function xdp_convert_buff_to_frame() may return NULL if it fails
to correctly convert the XDP buffer into an XDP frame due to memory
constraints, internal errors, or invalid data. Failing to check for NULL
may lead to a NULL pointer dereference if the result is used later in
processing, potentially causing crashes, data corruption, or undefined
behavior.
On XDP redirect failure, the associated page must be released explicitly
if it was previously retained via get_page(). Failing to do so may result
in a memory leak, as the pages reference count is not decremented. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: Require CAP_SYS_ADMIN for all usages of TIOCL_SELMOUSEREPORT
This requirement was overeagerly loosened in commit 2f83e38a095f
("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as
it turns out,
(1) the logic I implemented there was inconsistent (apologies!),
(2) TIOCL_SELMOUSEREPORT might actually be a small security risk
after all, and
(3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse
daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN
already.
In more detail:
1. The previous patch has inconsistent logic:
In commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes
without CAP_SYS_ADMIN"), we checked for sel_mode ==
TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of
this "mode" parameter were actually used as an additional way to
pass an argument. So the patch did actually still require
CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not
require it if none of the mouse buttons bits are set.
This logic is inconsistent and was not intentional. We should have
the same policies for using TIOCL_SELMOUSEREPORT independent of the
value of the "hidden" mouse button argument.
I sent a separate documentation patch to the man page list with
more details on TIOCL_SELMOUSEREPORT:
https://lore.kernel.org/all/[email protected]/
2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can
let an attacker simulate "keyboard" input to command line
applications on the same terminal, like TIOCSTI and some other
TIOCLINUX "selection mode" IOCTLs.
By enabling mouse reporting on a terminal and then injecting mouse
reports through TIOCL_SELMOUSEREPORT, an attacker can simulate
mouse movements on the same terminal, similar to the TIOCSTI
keystroke injection attacks that were previously possible with
TIOCSTI and other TIOCL_SETSEL selection modes.
Many programs (including libreadline/bash) are then prone to
misinterpret these mouse reports as normal keyboard input because
they do not expect input in the X11 mouse protocol form. The
attacker does not have complete control over the escape sequence,
but they can at least control the values of two consecutive bytes
in the binary mouse reporting escape sequence.
I went into more detail on that in the discussion at
https://lore.kernel.org/all/[email protected]/
It is not equally trivial to simulate arbitrary keystrokes as it
was with TIOCSTI (commit 83efeeeb3d04 ("tty: Allow TIOCSTI to be
disabled")), but the general mechanism is there, and together with
the small number of existing legit use cases (see below), it would
be better to revert back to requiring CAP_SYS_ADMIN for
TIOCL_SELMOUSEREPORT, as it was already the case before
commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without
CAP_SYS_ADMIN").
3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or
Consolation), and they are the only legit use case:
To quote console_codes(4):
The mouse tracking facility is intended to return
xterm(1)-compatible mouse status reports. Because the console
driver has no way to know the device or type of the mouse, these
reports are returned in the console input stream only when the
virtual terminal driver receives a mouse update ioctl. These
ioctls must be generated by a mouse-aware user-mode application
such as the gpm(8) daemon.
Jared Finder has also confirmed in
https://lore.kernel.org/all/[email protected]/
that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it
would be difficult to find good reasons for doing that, given that
it would interfere with the reports that GPM is sending.
More information on the interaction between GPM, terminals and th
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Fix invalid pointer dereference in Etron workaround
This check is performed before prepare_transfer() and prepare_ring(), so
enqueue can already point at the final link TRB of a segment. And indeed
it will, some 0.4% of times this code is called.
Then enqueue + 1 is an invalid pointer. It will crash the kernel right
away or load some junk which may look like a link TRB and cause the real
link TRB to be replaced with a NOOP. This wouldn't end well.
Use a functionally equivalent test which doesn't dereference the pointer
and always gives correct result.
Something has crashed my machine twice in recent days while playing with
an Etron HC, and a control transfer stress test ran for confirmation has
just crashed it again. The same test passes with this patch applied. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix WARNING "do not call blocking ops when !TASK_RUNNING"
wait_event_timeout() will set the state of the current
task to TASK_UNINTERRUPTIBLE, before doing the condition check. This
means that ksmbd_durable_scavenger_alive() will try to acquire the mutex
while already in a sleeping state. The scheduler warns us by giving
the following warning:
do not call blocking ops when !TASK_RUNNING; state=2 set at
[<0000000061515a6f>] prepare_to_wait_event+0x9f/0x6c0
WARNING: CPU: 2 PID: 4147 at kernel/sched/core.c:10099 __might_sleep+0x12f/0x160
mutex lock is not needed in ksmbd_durable_scavenger_alive(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-imx: Add check for spi_imx_setupxfer()
Add check for the return value of spi_imx_setupxfer().
spi_imx->rx and spi_imx->tx function pointer can be NULL when
spi_imx_setupxfer() return error, and make NULL pointer dereference.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
0x0
spi_imx_pio_transfer+0x50/0xd8
spi_imx_transfer_one+0x18c/0x858
spi_transfer_one_message+0x43c/0x790
__spi_pump_transfer_message+0x238/0x5d4
__spi_sync+0x2b0/0x454
spi_write_then_read+0x11c/0x200 |
| In the Linux kernel, the following vulnerability has been resolved:
driver core: fix potential NULL pointer dereference in dev_uevent()
If userspace reads "uevent" device attribute at the same time as another
threads unbinds the device from its driver, change to dev->driver from a
valid pointer to NULL may result in crash. Fix this by using READ_ONCE()
when fetching the pointer, and take bus' drivers klist lock to make sure
driver instance will not disappear while we access it.
Use WRITE_ONCE() when setting the driver pointer to ensure there is no
tearing. |
| In the Linux kernel, the following vulnerability has been resolved:
vmxnet3: Fix malformed packet sizing in vmxnet3_process_xdp
vmxnet3 driver's XDP handling is buggy for packet sizes using ring0 (that
is, packet sizes between 128 - 3k bytes).
We noticed MTU-related connectivity issues with Cilium's service load-
balancing in case of vmxnet3 as NIC underneath. A simple curl to a HTTP
backend service where the XDP LB was doing IPIP encap led to overly large
packet sizes but only for *some* of the packets (e.g. HTTP GET request)
while others (e.g. the prior TCP 3WHS) looked completely fine on the wire.
In fact, the pcap recording on the backend node actually revealed that the
node with the XDP LB was leaking uninitialized kernel data onto the wire
for the affected packets, for example, while the packets should have been
152 bytes their actual size was 1482 bytes, so the remainder after 152 bytes
was padded with whatever other data was in that page at the time (e.g. we
saw user/payload data from prior processed packets).
We only noticed this through an MTU issue, e.g. when the XDP LB node and
the backend node both had the same MTU (e.g. 1500) then the curl request
got dropped on the backend node's NIC given the packet was too large even
though the IPIP-encapped packet normally would never even come close to
the MTU limit. Lowering the MTU on the XDP LB (e.g. 1480) allowed to let
the curl request succeed (which also indicates that the kernel ignored the
padding, and thus the issue wasn't very user-visible).
Commit e127ce7699c1 ("vmxnet3: Fix missing reserved tailroom") was too eager
to also switch xdp_prepare_buff() from rcd->len to rbi->len. It really needs
to stick to rcd->len which is the actual packet length from the descriptor.
The latter we also feed into vmxnet3_process_xdp_small(), by the way, and
it indicates the correct length needed to initialize the xdp->{data,data_end}
parts. For e127ce7699c1 ("vmxnet3: Fix missing reserved tailroom") the
relevant part was adapting xdp_init_buff() to address the warning given the
xdp_data_hard_end() depends on xdp->frame_sz. With that fixed, traffic on
the wire looks good again. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: cmis_cdb: use correct rpl size in ethtool_cmis_module_poll()
rpl is passed as a pointer to ethtool_cmis_module_poll(), so the correct
size of rpl is sizeof(*rpl) which should be just 1 byte. Using the
pointer size instead can cause stack corruption:
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ethtool_cmis_wait_for_cond+0xf4/0x100
CPU: 72 UID: 0 PID: 4440 Comm: kworker/72:2 Kdump: loaded Tainted: G OE 6.11.0 #24
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. PowerEdge R760/04GWWM, BIOS 1.6.6 09/20/2023
Workqueue: events module_flash_fw_work
Call Trace:
<TASK>
panic+0x339/0x360
? ethtool_cmis_wait_for_cond+0xf4/0x100
? __pfx_status_success+0x10/0x10
? __pfx_status_fail+0x10/0x10
__stack_chk_fail+0x10/0x10
ethtool_cmis_wait_for_cond+0xf4/0x100
ethtool_cmis_cdb_execute_cmd+0x1fc/0x330
? __pfx_status_fail+0x10/0x10
cmis_cdb_module_features_get+0x6d/0xd0
ethtool_cmis_cdb_init+0x8a/0xd0
ethtool_cmis_fw_update+0x46/0x1d0
module_flash_fw_work+0x17/0xa0
process_one_work+0x179/0x390
worker_thread+0x239/0x340
? __pfx_worker_thread+0x10/0x10
kthread+0xcc/0x100
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2d/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
lib/iov_iter: fix to increase non slab folio refcount
When testing EROFS file-backed mount over v9fs on qemu, I encountered a
folio UAF issue. The page sanity check reports the following call trace.
The root cause is that pages in bvec are coalesced across a folio bounary.
The refcount of all non-slab folios should be increased to ensure
p9_releas_pages can put them correctly.
BUG: Bad page state in process md5sum pfn:18300
page: refcount:0 mapcount:0 mapping:00000000d5ad8e4e index:0x60 pfn:0x18300
head: order:0 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
aops:z_erofs_aops ino:30b0f dentry name(?):"GoogleExtServicesCn.apk"
flags: 0x100000000000041(locked|head|node=0|zone=1)
raw: 0100000000000041 dead000000000100 dead000000000122 ffff888014b13bd0
raw: 0000000000000060 0000000000000020 00000000ffffffff 0000000000000000
head: 0100000000000041 dead000000000100 dead000000000122 ffff888014b13bd0
head: 0000000000000060 0000000000000020 00000000ffffffff 0000000000000000
head: 0100000000000000 0000000000000000 ffffffffffffffff 0000000000000000
head: 0000000000000010 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
Call Trace:
dump_stack_lvl+0x53/0x70
bad_page+0xd4/0x220
__free_pages_ok+0x76d/0xf30
__folio_put+0x230/0x320
p9_release_pages+0x179/0x1f0
p9_virtio_zc_request+0xa2a/0x1230
p9_client_zc_rpc.constprop.0+0x247/0x700
p9_client_read_once+0x34d/0x810
p9_client_read+0xf3/0x150
v9fs_issue_read+0x111/0x360
netfs_unbuffered_read_iter_locked+0x927/0x1390
netfs_unbuffered_read_iter+0xa2/0xe0
vfs_iocb_iter_read+0x2c7/0x460
erofs_fileio_rq_submit+0x46b/0x5b0
z_erofs_runqueue+0x1203/0x21e0
z_erofs_readahead+0x579/0x8b0
read_pages+0x19f/0xa70
page_cache_ra_order+0x4ad/0xb80
filemap_readahead.isra.0+0xe7/0x150
filemap_get_pages+0x7aa/0x1890
filemap_read+0x320/0xc80
vfs_read+0x6c6/0xa30
ksys_read+0xf9/0x1c0
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x71/0x79 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in __smb2_lease_break_noti()
Move tcp_transport free to ksmbd_conn_free. If ksmbd connection is
referenced when ksmbd server thread terminates, It will not be freed,
but conn->tcp_transport is freed. __smb2_lease_break_noti can be performed
asynchronously when the connection is disconnected. __smb2_lease_break_noti
calls ksmbd_conn_write, which can cause use-after-free
when conn->ksmbd_transport is already freed. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in smb_break_all_levII_oplock()
There is a room in smb_break_all_levII_oplock that can cause racy issues
when unlocking in the middle of the loop. This patch use read lock
to protect whole loop. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau: prime: fix ttm_bo_delayed_delete oops
Fix an oops in ttm_bo_delayed_delete which results from dererencing a
dangling pointer:
Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b7b: 0000 [#1] PREEMPT SMP
CPU: 4 UID: 0 PID: 1082 Comm: kworker/u65:2 Not tainted 6.14.0-rc4-00267-g505460b44513-dirty #216
Hardware name: LENOVO 82N6/LNVNB161216, BIOS GKCN65WW 01/16/2024
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:dma_resv_iter_first_unlocked+0x55/0x290
Code: 31 f6 48 c7 c7 00 2b fa aa e8 97 bd 52 ff e8 a2 c1 53 00 5a 85 c0 74 48 e9 88 01 00 00 4c 89 63 20 4d 85 e4 0f 84 30 01 00 00 <41> 8b 44 24 10 c6 43 2c 01 48 89 df 89 43 28 e8 97 fd ff ff 4c 8b
RSP: 0018:ffffbf9383473d60 EFLAGS: 00010202
RAX: 0000000000000001 RBX: ffffbf9383473d88 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffbf9383473d78 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 6b6b6b6b6b6b6b6b
R13: ffffa003bbf78580 R14: ffffa003a6728040 R15: 00000000000383cc
FS: 0000000000000000(0000) GS:ffffa00991c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000758348024dd0 CR3: 000000012c259000 CR4: 0000000000f50ef0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body.cold+0x19/0x26
? die_addr+0x3d/0x70
? exc_general_protection+0x159/0x460
? asm_exc_general_protection+0x27/0x30
? dma_resv_iter_first_unlocked+0x55/0x290
dma_resv_wait_timeout+0x56/0x100
ttm_bo_delayed_delete+0x69/0xb0 [ttm]
process_one_work+0x217/0x5c0
worker_thread+0x1c8/0x3d0
? apply_wqattrs_cleanup.part.0+0xc0/0xc0
kthread+0x10b/0x240
? kthreads_online_cpu+0x140/0x140
ret_from_fork+0x40/0x70
? kthreads_online_cpu+0x140/0x140
ret_from_fork_asm+0x11/0x20
</TASK>
The cause of this is:
- drm_prime_gem_destroy calls dma_buf_put(dma_buf) which releases the
reference to the shared dma_buf. The reference count is 0, so the
dma_buf is destroyed, which in turn decrements the corresponding
amdgpu_bo reference count to 0, and the amdgpu_bo is destroyed -
calling drm_gem_object_release then dma_resv_fini (which destroys the
reservation object), then finally freeing the amdgpu_bo.
- nouveau_bo obj->bo.base.resv is now a dangling pointer to the memory
formerly allocated to the amdgpu_bo.
- nouveau_gem_object_del calls ttm_bo_put(&nvbo->bo) which calls
ttm_bo_release, which schedules ttm_bo_delayed_delete.
- ttm_bo_delayed_delete runs and dereferences the dangling resv pointer,
resulting in a general protection fault.
Fix this by moving the drm_prime_gem_destroy call from
nouveau_gem_object_del to nouveau_bo_del_ttm. This ensures that it will
be run after ttm_bo_delayed_delete. |
