| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
rmi_f30_map_gpios() allocates gpioled_key_map with
min(gpioled_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f30_attention() iterates the full f30->gpioled_count (device query
register, range 0..31) and dereferences gpioled_key_map[i], and
input->keycodemax is set to the full gpioled_count while input->keycode
points at the 6-entry allocation.
A device that reports gpioled_count > 6 with GPIO support enabled
therefore causes an out-of-bounds read on the attention interrupt and
out-of-bounds read/write through the EVIOCGKEYCODE/EVIOCSKEYCODE ioctls,
which bound the index only against keycodemax. This is the same defect
as the F3A handler, which was copied from F30.
Size the keymap for the full gpioled_count; the mapping loop still
assigns only the first min(gpioled_count, TRACKSTICK_RANGE_END) entries. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - prevent division by zero and arithmetic underflow
The Elan I2C touchpad driver queries the device for its physical
dimensions and trace counts to calculate the device resolution and width.
However, if the device firmware or device tree provides invalid zero
values for x_traces or y_traces, it results in a fatal division-by-zero
exception leading to a kernel panic during device probe.
Add checks to ensure these parameters are non-zero before performing
the division. If invalid trace values are detected, fall back to a safe
default of 1.
Additionally, prevent an arithmetic underflow in the touch reporting
logic. Previously, if the calculated or fallback width was smaller than
ETP_FWIDTH_REDUCE (90), the subtraction would underflow, resulting in a
massive unsigned integer being reported to userspace. Clamp the adjusted
width to a minimum of 0 to safely handle small physical dimensions and
fallback scenarios.
Completing the probe with safe fallback values ensures the sysfs nodes
are created, keeping the firmware update path intact so a recovery
firmware can be flashed to the device. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - reject an oversized device packet size
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device register byte (0x0F) and the only check
is the lower bound packet_size <= 0; it is never bounded against the
size of touch[]. A malfunctioning, malicious or counterfeit controller
(or an attacker tampering with the I2C bus) can report a packet_size of
up to 255, so __mms114_read_reg() writes up to 175 bytes past the end of
touch[] on the IRQ-thread stack: a stack out-of-bounds write that can
overwrite the stack canary, saved registers and the return address.
A well-formed device never reports more than the buffer holds, so reject
an oversized packet and drop the report, consistent with the handler's
other error paths, rather than reading past the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
When the server answers an RTRS READ, rdma_write_sg() builds the source
scatter/gather entry for the IB_WR_RDMA_WRITE that returns data to the
peer. Its length is taken directly from the wire descriptor:
plist->length = le32_to_cpu(id->rd_msg->desc[0].len);
rd_msg points into the chunk buffer that the remote peer filled via
RDMA-WRITE-WITH-IMM (rtrs_srv_rdma_done() -> process_io_req() ->
process_read()), so desc[0].len is attacker-controlled and, before this
change, was only rejected when zero. The source address is the fixed
chunk start (dma_addr[msg_id]) and the source lkey is the PD-wide
local_dma_lkey, which is not tied to the chunk's MR mapping, so the verbs
layer does not constrain the transfer length to max_chunk_size. msg_id
and off are bounded against queue_depth and max_chunk_size in
rtrs_srv_rdma_done(), but desc[0].len is a separate field that was not
checked against the chunk size.
A peer that advertises desc[0].len larger than max_chunk_size can make
the posted RDMA write read past the chunk's mapped region. The resulting
behaviour depends on the IOMMU configuration: with no IOMMU or in
passthrough mode the read may extend into memory adjacent to the chunk
and be returned to the peer, which can disclose host memory; with a
translating IOMMU the out-of-range access is expected to fault and abort
the connection. In either case the transfer exceeds what the protocol
permits and is driven by a remote peer.
Reject a descriptor length above max_chunk_size, mirroring the existing
off >= max_chunk_size bound in rtrs_srv_rdma_done(). Legitimate clients
do not exceed it: the client sets desc[0].len to its MR length, which is
capped at the negotiated max_io_size (max_chunk_size - MAX_HDR_SIZE). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: bound Read Response placement to the RREAD length
In drivers/infiniband/sw/siw/siw_qp_rx.c, siw_proc_rresp() places each
inbound Read Response DDP segment at sge->laddr + wqe->processed and then
accumulates wqe->processed, but it never checks the running total against
the sink buffer length on continuation segments. siw_check_sge() resolves
and validates the sink memory only on the first fragment (the if (!*mem)
branch), and siw_rresp_check_ntoh() compares the cumulative length against
wqe->bytes only on the final segment (the !frx->more_ddp_segs guard).
A connected siw peer that answers an outstanding RREAD with Read Response
segments that keep the DDP Last flag clear, carrying more total payload
than the RREAD requested, drives wqe->processed past the validated sink
buffer; the next siw_rx_data() call writes out of bounds at
sge->laddr + wqe->processed. siw runs iWARP over ordinary routable TCP,
so the peer is the remote end of an established RDMA connection and needs
no local privilege.
Bound every segment before placement, exactly as siw_proc_send() and
siw_proc_write() already do for their tagged and untagged paths, and
terminate the connection with a base-or-bounds DDP error when the
Read Response would overrun the sink buffer.
This is the second receive-path length fix for this file. A separate
change rejects an MPA FPDU length that underflows the per-fragment
remainder in the header decode; that guard does not cover this case,
because here each individual segment length is self-consistent and only
the accumulated placement offset overruns the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: avoid 32-bit prune notification count wrap
FUSE_NOTIFY_PRUNE validates the nodeid payload length with:
size - sizeof(outarg) != outarg.count * sizeof(u64)
On 32-bit kernels, size_t is also 32 bits, so the daemon-controlled
count multiplication can wrap. A prune notification with count
0x20000000 and no nodeid payload passes the check, enters the copy
loop, and asks the device copy path to read nodeids that are not
present in the userspace write buffer. In QEMU this reaches the
fuse_copy_fill() BUG_ON(!err) path.
Validate the payload length with array_size() instead. That accepts
exactly the same valid messages, but avoids wrapping arithmetic before
the copy loop consumes the count. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: re-lock request before returning from fuse_ref_folio()
fuse_ref_folio() unlocks the request but does not re-lock it before
returning. fuse_chan_abort() can end the request and the async end
callback (eg fuse_writepage_free()) can free the args while the
subsequent copy chain logic after fuse_ref_folio() accesses them,
leading to use-after-free issues.
Fix this by locking the request in fuse_ref_folio() before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: clear intr_entry in fuse_resend and fuse_remove_pending_req
When fuse_resend() moves a request from fpq->processing back to
fiq->pending, it sets FR_PENDING and clears FR_SENT but does not
remove the requests intr_entry from fiq->interrupts. If the
request had FR_INTERRUPTED set from a prior signal, intr_entry
remains dangling on fiq->interrupts. When the requesting task
then receives a fatal signal, fuse_remove_pending_req() sees
FR_PENDING=1, removes the request from fiq->pending and frees it
via the refcount path, also without cleaning intr_entry. The
stale intr_entry causes use-after-free when fuse_read_interrupt()
iterates fiq->interrupts:
- list_del_init(&req->intr_entry) -> UAF write on freed slab
- req->in.h.unique -> UAF read, data leaked to userspace
Remove intr_entry from fiq->interrupts in fuse_resend() for
interrupted requests before they are placed back on fiq->pending.
Add a WARN_ON if the intr_entry is not empty on request destruction. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix EFAULT clobber in fuse_uring_commit
copy_from_user() returns the number of bytes not copied as an unsigned
residual on failure (1..sizeof(struct fuse_out_header)). fuse_uring_commit
stores that residual in ssize_t err, sets req->out.h.error to -EFAULT,
then jumps to out: with err still holding the positive residual.
err = copy_from_user(&req->out.h, &ent->headers->in_out,
sizeof(req->out.h));
if (err) {
req->out.h.error = -EFAULT;
goto out; /* err is the positive residual */
}
...
out:
fuse_uring_req_end(ent, req, err);
fuse_uring_req_end() then runs
if (error)
req->out.h.error = error;
which overwrites the just-assigned -EFAULT with the positive residual.
FUSE callers such as fuse_simple_request() test err < 0 to detect
failure, so the positive value is interpreted as success and the
caller proceeds with an uninitialised or partial req->out.args.
Fix by assigning err = -EFAULT in the failure branch before jumping
to out, so fuse_uring_req_end() receives a negative errno and sets
req->out.h.error to -EFAULT. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix moving cancelled entry to ent_in_userspace list
fuse_uring_cancel() moves entries that are available (these have no reqs
attached) to the ent_in_userspace list. ent_list_request_expired()
checks the first entry on ent_in_userspace and dereferences
ent->fuse_req unconditionally, which will crash on a cancelled entry
that was moved to this list.
Fix this by freeing the entry and dropping queue_refs directly in
fuse_uring_cancel(). This is safe because cancel is the cancel handler
itself - after io_uring_cmd_done(), no more cancels will be dispatched
for this command, and teardown serializes with cancel via queue->lock.
Since cancel now decrements queue_refs, fuse_uring_abort() must no
longer gate fuse_uring_abort_end_requests() on queue_refs > 0, as
cancelled entries may have already dropped queue_refs while requests are
still queued. Remove the gate so abort always flushes requests and stops
queues. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: end fuse_req on io-uring cancel task work
When io_uring delivers task work with tw.cancel set (PF_EXITING,
PF_KTHREAD fallback, or percpu_ref_is_dying on the ring context),
fuse_uring_send_in_task() takes the cancel branch, assigns
-ECANCELED, and falls through to fuse_uring_send(). That path only
flips the entry to FRRS_USERSPACE and completes the io_uring cmd;
it never discharges the ring entry's owning reference to the
fuse_req that fuse_uring_add_req_to_ring_ent() handed it at
dispatch time.
fuse_uring_send_in_task()
tw.cancel == true
err = -ECANCELED
fuse_uring_send(ent, cmd, err, issue_flags)
ent->state = FRRS_USERSPACE
list_move(&ent->list, &queue->ent_in_userspace)
ent->cmd = NULL
io_uring_cmd_done(-ECANCELED)
/* ent->fuse_req still set, req still hashed */
The fuse_req stays linked on fpq->processing[hash] and
fuse_request_end() is never invoked. The originating syscall
thread blocks in D-state in request_wait_answer() until
fuse_abort_conn() runs, which can be the entire connection
lifetime. For FR_BACKGROUND requests fc->num_background is never
decremented either, so repeated cancels inflate the counter until
max_background is hit and all later background ops stall. tw.cancel does
not imply a connection abort (e.g. a single io_uring worker thread exits
while the fuse connection stays up), so this cannot be left for
fuse_abort_conn() to clean up.
Ending the req but still routing the entry through fuse_uring_send()
is not enough: that leaves a req-less entry on ent_in_userspace, and
ent_list_request_expired() dereferences ent->fuse_req unconditionally
on the head of that list, which would then NULL-deref.
Fix the cancel branch to release the entry directly. Remove it from the
queue, complete the io_uring cmd, end the fuse_req, free the entry, and
drop its queue_refs (waking the teardown waiter if it was the last). |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid use-after-free in fuse_uring_async_stop_queues
fuse_uring_async_stop_queues() might run when the last reference
on ring->queue_refs was already dropped.
In order to avoid an early destruction a reference on struct fuse_conn
is now taken before starting fuse_uring_async_stop_queues() and that
reference is only released when that delayed work queue terminates. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid queue->stopped races and set/read that value under lock
There are several readers of queue->stopped that check the value
under lock, but fuse_uring_commit_fetch() did not and actually
the value was not set under the lock in fuse_uring_abort_end_requests()
either. Especially in fuse_uring_commit_fetch it is important
to check under a lock, because due to races 'struct fuse_req'
might be freed with fuse_request_end, but another thread/cpu
might already do teardown work. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: make a fuse_req on SQE commit only findable after memcpy
Bad userspace might try to trick us and send commit SQEs request
unique / commit-id of requests that are not even send to
fuse-server (io_uring_cmd_done() not called) yet.
fuse_uring_commit_fetch() ends the fuse request when the ring entry
has a wrong state, but that could have caused a use-after-free
with the memcpy operations in fuse_uring_send_in_task().
In order to avoid such races the call of fuse_uring_add_to_pq()
is moved after the copy operations and just before completing
the io-uring request - malicious userspace cannot find the request
anymore until all prepration work in fuse-client/kernel is completed.
This also moves fuse_uring_add_to_pq() a bit up in the code to
avoid a forward declaration. Also not with a preparation commit,
to make it easier to back port to older kernels. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: remove request-less entries from ent_w_req_queue to fix NULL deref
If a copy into the userspace ring buffer fails, a request will be
terminated and fuse_uring_req_end() will set ent->fuse_req to NULL but
it will leave the entry on ent_w_req_queue in FRRS_FUSE_REQ state. This
can lead to a NULL deref if the request expiration logic scans
ent_w_req_queue in the window before the entry is moved off it.
Fix this by taking the entry off ent_w_req_queue and changing its state
from FRRS_FUSE_REQ to FRRS_INVALID before terminating the request. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions. |
