| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-ads1298: add bounds check to pga_settings index
ads1298_pga_settings has 7 elements but ADS1298_MASK_CH_PGA can yield
values 0-7. If it yields a value >= 7, this causes an out-of-bounds
array access. Add a bounds check and return -EINVAL if the index
is out of range.
Note that the remaining value b111 is reserved so should not be seen
in a correctly functioning system. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vce: Prevent partial address patches
In the case that only one of lo/hi is valid, the patching could result
in a bad address written to in FW. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: validate connector number in ucsi_connector_change()
The connector number in a UCSI CCI notification is a 7-bit field
supplied by the PPM. ucsi_connector_change() uses it to index the
ucsi->connector[] array without checking it against the number of
connectors the PPM reported at init time, so a buggy or malicious PPM
(EC firmware, or an I2C-attached UCSI controller on the ccg / stm32g0 /
glink transports) can drive schedule_work() on memory past the end of
the array.
Reject connector numbers that are zero or exceed cap.num_connectors
before dereferencing the array. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Remove latent out-of-bounds access in IOMMU debugfs
In iommu_mmio_write() and iommu_capability_write(), the variables
dbg_mmio_offset and dbg_cap_offset are declared as int. However, they
are populated using kstrtou32_from_user(). If a user provides a
sufficiently large value, it can become a negative integer.
Prior to this patch, the AMD IOMMU debugfs implementation was already
protected by different mechanisms.
1. #define OFS_IN_SZ 8 ensures the user string <= 8 bytes, so
e.g. 0xffffffff isn't a valid input.
if (cnt > OFS_IN_SZ)
return -EINVAL;
2. Implicit type promotion in iommu_mmio_write(), dbg_mmio_offset is int
and iommu->mmio_phys_end is u64
if (dbg_mmio_offset > iommu->mmio_phys_end - sizeof(u64))
return -EINVAL;
3. The show handlers would currently catch the negative number and
refuse to perform the read.
Replace kstrtou32_from_user() with kstrtos32_from_user() to parse the
input, and check for negative values to explicitly prevent out-of-bounds
memory accesses directly in iommu_mmio_write() and
iommu_capability_write(). |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: omninet: fix memory corruption with small endpoint
Make sure that the bulk-out buffers are at least as large as the
hardcoded transfer size to avoid user-controlled slab corruption should
a malicious device report a smaller endpoint max packet size than
expected. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: rsnd: Fix potential out-of-bounds access of component_dais[]
component_dais[RSND_MAX_COMPONENT] is initially zero-initialized
and later populated in rsnd_dai_of_node(). However, the existing boundary check:
if (i >= RSND_MAX_COMPONENT)
does not guarantee that the last valid element remains zero. As a result,
the loop can rely on component_dais[RSND_MAX_COMPONENT] being zero,
which may lead to an out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Require in-GHCB scratch area if GHCB v2+ is in use
As per the GHCB spec, when using GHCB v2+ require the software scratch area
to reside in the GHCB's shared buffer. Note, things like Page State Change
(PSC) requests _rely_ on this behavior, as the guest can't provide a length
when making the request, i.e. the size of the guest payload is bounded by
the size of the shared buffer.
Failure to force usage of the GHCB, and a slew of other flaws, lets a
malicious SNP guest corrupt host kernel heap memory, and leak host heap
layout information.
setup_vmgexit_scratch() allocates a buffer via kvzalloc(exit_info_2),
where exit_info_2 is guest-controlled. With exit_info_2=24, this yields
a 24-byte allocation in kmalloc-cg-32 (32-byte slab objects). The buffer
holds an 8-byte psc_hdr followed by 8-byte psc_entry structs, so only
entries[0] and entries[1] are in-bounds.
snp_begin_psc() validates end_entry against VMGEXIT_PSC_MAX_COUNT (253)
but NOT against the actual buffer size:
idx_end = hdr->end_entry;
if (idx_end >= VMGEXIT_PSC_MAX_COUNT) { // checks 253, not buffer
snp_complete_psc(svm, ...);
return 1;
}
for (idx = idx_start; idx <= idx_end; idx++) {
entry_start = entries[idx]; // OOB when idx >= 2
The guest sets end_entry=10+, causing the host to iterate entries[2+]
which are OOB into adjacent slab objects. For each OOB entry:
- The host reads 8 bytes (OOB READ / info leak oracle)
- If the data passes PSC validation, __snp_complete_one_psc() writes
cur_page = 1 or 512 into the entry (OOB WRITE, sev.c:3806)
- If validation fails, the error response reveals whether adjacent
memory is zero vs non-zero (information disclosure to guest)
The guest controls allocation size (exit_info_2), entry range
(cur_entry/end_entry), and can fire unlimited VMGEXITs to repeatedly
hit different slab positions.
By exploiting the variety of bugs, a malicious SEV-SNP guest can:
- OOB read adjacent kmalloc-cg-32 objects (heap layout disclosure)
- OOB write cur_page bits into adjacent objects (heap corruption)
- Trigger use-after-free conditions across VMGEXITs
E.g. with KASAN enabled, a single insmod of the PoC guest module
produces 73 KASAN reports:
BUG: KASAN: slab-out-of-bounds in snp_begin_psc+0x126/0x890
Read of size 8 at addr ffff888219ffb5e0 by task qemu-system-x86/2199
BUG: KASAN: slab-out-of-bounds in snp_begin_psc+0x468/0x890
Write of size 8 at addr ffff888351566648 by task qemu-system-x86/2199
The buggy address belongs to the object at ffff888XXXXXXXXX
which belongs to the cache kmalloc-cg-32 of size 32
The buggy address is located N bytes to the right of
allocated 32-byte region [ffff888XXXXXXXXX, ffff888XXXXXXXXX)
Breakdown:
62 slab-out-of-bounds (reads + writes past allocation)
7 slab-use-after-free
4 use-after-free
All credit to Stan for the wonderful description and reproducer!
[sean: write changelog] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
(cherry picked from commit 37668568641ccc4cc1dbca4923d0a16609dd5707) |
| An out-of-bounds write vulnerability in the Productivity Suite allows a
local attacker to trigger kernel memory corruption via a crafted IOCTL
request, potentially resulting in privilege escalation or system
instability. |
| An out-of-bounds write vulnerability in the Productivity Suite allows a
local attacker to trigger kernel memory corruption via a crafted IOCTL
request, potentially resulting in privilege escalation or system
instability. |
| Quicly is an IETF QUIC protocol implementation intended primarily for use within the H2O HTTP server. Prior to commit 8b178e6, Quicly is vulnerable to a Denial of Service attack through connection state corruption. In QUIC Invariants, the maximum length of a Connection ID is 255 bytes, while QUIC version 1 further restricts the maximum to 20 bytes. Quicly implements QUIC version 1 and therefore its CID buffers are limited to 20 bytes. However, to be able to respond to unknown versions of QUIC, its packet decoder accepts Connection IDs of up to 255 bytes. As its CID buffers are merely 20 bytes long, Quicly must reject QUIC version 1 packets with Connection IDs longer than that. The command line tool bundled with Quicly has had that check, however the library itself lacked such enforcement. As a consequence, when used by applications that lack their own enforcement, the connection state becoming inconsistent to buffer overrun. Fortunately, the overflow stops within the allocated chunk of memory, but nevertheless, the bug leads to assertion failures. This issue has been fixed by commit 8b178e6. |
| The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy. |
| TDengine is an open source, time-series database optimized for Internet of Things devices. In 3.4.1.6 and earlier, source/libs/parser/src/parUtil.c trimString() checks space for only one byte before processing SQL string escape sequences \%, \_, or \x, allowing a one-byte out-of-bounds write to the stack buffer tmpTokenBuf that can cause denial of service and potentially remote code execution. This issue is fixed in version 3.4.1.14. |
| Premiere Pro is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Audition is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Audition is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Pillow is a Python imaging library. Prior to 12.3.0, Pillow public image coordinate APIs can trigger a native heap out-of-bounds write when given coordinates near the signed 32-bit integer limits in Image.paste(), Image.crop(), or Image.alpha_composite(). This issue is fixed in version 12.3.0. |
| Premiere Pro is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Audition is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Audition is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
