| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| FlashMQ is a MQTT broker/server, designed for multi-CPU environments. Prior to version 1.26.1, a remote client with retained publish permission can crash the FlashMQ broker when both set_retained_message_defer_timeout and set_retained_message_defer_timeout_spread are configured to non-default values, resulting in denial of service. If anonymous retained publishing is allowed, no authentication is required; otherwise, the attacker needs the corresponding publish permission. This issue has been patched in version 1.26.1. |
| In the Linux kernel, the following vulnerability has been resolved:
9p/xen: protect xen_9pfs_front_free against concurrent calls
The xenwatch thread can race with other back-end change notifications
and call xen_9pfs_front_free() twice, hitting the observed general
protection fault due to a double-free. Guard the teardown path so only
one caller can release the front-end state at a time, preventing the
crash.
This is a fix for the following double-free:
[ 27.052347] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[ 27.052357] CPU: 0 UID: 0 PID: 32 Comm: xenwatch Not tainted 6.18.0-02087-g51ab33fc0a8b-dirty #60 PREEMPT(none)
[ 27.052363] RIP: e030:xen_9pfs_front_free+0x1d/0x150
[ 27.052368] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 41 55 41 54 55 48 89 fd 48 c7 c7 48 d0 92 85 53 e8 cb cb 05 00 48 8b 45 08 48 8b 55 00 <48> 3b 28 0f 85 f9 28 35 fe 48 3b 6a 08 0f 85 ef 28 35 fe 48 89 42
[ 27.052377] RSP: e02b:ffffc9004016fdd0 EFLAGS: 00010246
[ 27.052381] RAX: 6b6b6b6b6b6b6b6b RBX: ffff88800d66e400 RCX: 0000000000000000
[ 27.052385] RDX: 6b6b6b6b6b6b6b6b RSI: 0000000000000000 RDI: 0000000000000000
[ 27.052389] RBP: ffff88800a887040 R08: 0000000000000000 R09: 0000000000000000
[ 27.052393] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888009e46b68
[ 27.052397] R13: 0000000000000200 R14: 0000000000000000 R15: ffff88800a887040
[ 27.052404] FS: 0000000000000000(0000) GS:ffff88808ca57000(0000) knlGS:0000000000000000
[ 27.052408] CS: e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 27.052412] CR2: 00007f9714004360 CR3: 0000000004834000 CR4: 0000000000050660
[ 27.052418] Call Trace:
[ 27.052420] <TASK>
[ 27.052422] xen_9pfs_front_changed+0x5d5/0x720
[ 27.052426] ? xenbus_otherend_changed+0x72/0x140
[ 27.052430] ? __pfx_xenwatch_thread+0x10/0x10
[ 27.052434] xenwatch_thread+0x94/0x1c0
[ 27.052438] ? __pfx_autoremove_wake_function+0x10/0x10
[ 27.052442] kthread+0xf8/0x240
[ 27.052445] ? __pfx_kthread+0x10/0x10
[ 27.052449] ? __pfx_kthread+0x10/0x10
[ 27.052452] ret_from_fork+0x16b/0x1a0
[ 27.052456] ? __pfx_kthread+0x10/0x10
[ 27.052459] ret_from_fork_asm+0x1a/0x30
[ 27.052463] </TASK>
[ 27.052465] Modules linked in:
[ 27.052471] ---[ end trace 0000000000000000 ]--- |
| Akamai Guardicore Platform Agent (GPA) and Zero Trust Client on Linux and macOS allow TOCTOU-based local privilege escalation. The GPA service creates an IPC socket in the world-writable /tmp directory. It accepts unauthenticated IPC control messages. This enables a TOCTOU vulnerability in the HandleSaveLogs() function of the GPA service, by creating a log file and manipulating it into a symlink that points to the targeted path; this can allow an unprivileged local user to make arbitrary root-owned files world-writable. In addition, a diagnostic collection tool (gimmelogs) running with root privileges was vulnerable to command injection from the dbstore, offering a second privilege escalation vector. (On Windows, gimmelogs does not have command injection but does allow writing a ZIP archive to an unintended location.) This affects Akamai Guardicore Platform Agent 7.0 through 7.3.1 and Akamai Zero Trust Client 6.0 through 6.1.5. |
| Race Condition in NetScaler ADC and NetScaler Gateway when appliance is configured as Gateway (SSL VPN, ICA Proxy, CVPN, RDP Proxy) or AAA virtual server leading to User Session Mixup |
| Due to multiple time-of-check time-of-use race conditions in the resource count check and increment logic, as well as missing validations, users of the platform are able to exceed the allocation limits configured for their accounts/domains. This can be used by an attacker to degrade the infrastructure's resources and lead to denial of service conditions.
Users are recommended to upgrade to Apache CloudStack versions 4.20.3.0 or 4.22.0.1, or later, which fixes this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Fix device cleanup order to prevent kernel panic
Move video device unregistration to the beginning of the remove function
to ensure all video operations are stopped before cleaning up the worker
thread and disabling PM runtime. This prevents hardware register access
after the device has been powered down.
In polling mode, the hrtimer periodically triggers
wave5_vpu_timer_callback() which queues work to the kthread worker.
The worker executes wave5_vpu_irq_work_fn() which reads hardware
registers via wave5_vdi_read_register().
The original cleanup order disabled PM runtime and powered down hardware
before unregistering video devices. When autosuspend triggers and powers
off the hardware, the video devices are still registered and the worker
thread can still be triggered by the hrtimer, causing it to attempt
reading registers from powered-off hardware. This results in a bus error
(synchronous external abort) and kernel panic.
This causes random kernel panics during encoding operations:
Internal error: synchronous external abort: 0000000096000010
[#1] PREEMPT SMP
Modules linked in: wave5 rpmsg_ctrl rpmsg_char ...
CPU: 0 UID: 0 PID: 1520 Comm: vpu_irq_thread
Tainted: G M W
pc : wave5_vdi_read_register+0x10/0x38 [wave5]
lr : wave5_vpu_irq_work_fn+0x28/0x60 [wave5]
Call trace:
wave5_vdi_read_register+0x10/0x38 [wave5]
kthread_worker_fn+0xd8/0x238
kthread+0x104/0x120
ret_from_fork+0x10/0x20
Code: aa1e03e9 d503201f f9416800 8b214000 (b9400000)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: synchronous external abort:
Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: fix potential zero beacon interval in beacon tracking
During fuzz testing, it was discovered that bss_conf->beacon_int
might be zero, which could result in a division by zero error in
subsequent calculations. Set a default value of 100 TU if the
interval is zero to ensure stability. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Flush exception handling work when RPM level is zero
Ensure that the exception event handling work is explicitly flushed during
suspend when the runtime power management level is set to UFS_PM_LVL_0.
When the RPM level is zero, the device power mode and link state both
remain active. Previously, the UFS core driver bypassed flushing exception
event handling jobs in this configuration. This created a race condition
where the driver could attempt to access the host controller to handle an
exception after the system had already entered a deep power-down state,
resulting in a system crash.
Explicitly flush this work and disable auto BKOPs before the suspend
callback proceeds. This guarantees that pending exception tasks complete
and prevents illegal hardware access during the power-down sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
mpls: add seqcount to protect the platform_label{,s} pair
The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have
an inconsistent view of platform_labels vs platform_label in case of a
concurrent resize (resize_platform_label_table, under
platform_mutex). This can lead to OOB accesses.
This patch adds a seqcount, so that we get a consistent snapshot.
Note that mpls_label_ok is also susceptible to this, so the check
against RTA_DST in rtm_to_route_config, done outside platform_mutex,
is not sufficient. This value gets passed to mpls_label_ok once more
in both mpls_route_add and mpls_route_del, so there is no issue, but
that additional check must not be removed. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Move iio_device_register() to correct location
iio_device_register() should be at the end of the probe function to
prevent race conditions.
Place iio_device_register() at the end of the probe function and place
iio_device_unregister() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mixer: oss: Add card disconnect checkpoints
ALSA OSS mixer layer calls the kcontrol ops rather individually, and
pending calls might be not always caught at disconnecting the device.
For avoiding the potential UAF scenarios, add sanity checks of the
card disconnection at each entry point of OSS mixer accesses. The
rwsem is taken just before that check, hence the rest context should
be covered by that properly. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: ensure safe access to master conntrack
Holding reference on the expectation is not sufficient, the master
conntrack object can just go away, making exp->master invalid.
To access exp->master safely:
- Grab the nf_conntrack_expect_lock, this gets serialized with
clean_from_lists() which also holds this lock when the master
conntrack goes away.
- Hold reference on master conntrack via nf_conntrack_find_get().
Not so easy since the master tuple to look up for the master conntrack
is not available in the existing problematic paths.
This patch goes for extending the nf_conntrack_expect_lock section
to address this issue for simplicity, in the cases that are described
below this is just slightly extending the lock section.
The add expectation command already holds a reference to the master
conntrack from ctnetlink_create_expect().
However, the delete expectation command needs to grab the spinlock
before looking up for the expectation. Expand the existing spinlock
section to address this to cover the expectation lookup. Note that,
the nf_ct_expect_iterate_net() calls already grabs the spinlock while
iterating over the expectation table, which is correct.
The get expectation command needs to grab the spinlock to ensure master
conntrack does not go away. This also expands the existing spinlock
section to cover the expectation lookup too. I needed to move the
netlink skb allocation out of the spinlock to keep it GFP_KERNEL.
For the expectation events, the IPEXP_DESTROY event is already delivered
under the spinlock, just move the delivery of IPEXP_NEW under the
spinlock too because the master conntrack event cache is reached through
exp->master.
While at it, add lockdep notations to help identify what codepaths need
to grab the spinlock. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Flush dev-IOTLB only when PCIe device is accessible in scalable mode
Commit 4fc82cd907ac ("iommu/vt-d: Don't issue ATS Invalidation
request when device is disconnected") relies on
pci_dev_is_disconnected() to skip ATS invalidation for
safely-removed devices, but it does not cover link-down caused
by faults, which can still hard-lock the system.
For example, if a VM fails to connect to the PCIe device,
"virsh destroy" is executed to release resources and isolate
the fault, but a hard-lockup occurs while releasing the group fd.
Call Trace:
qi_submit_sync
qi_flush_dev_iotlb
intel_pasid_tear_down_entry
device_block_translation
blocking_domain_attach_dev
__iommu_attach_device
__iommu_device_set_domain
__iommu_group_set_domain_internal
iommu_detach_group
vfio_iommu_type1_detach_group
vfio_group_detach_container
vfio_group_fops_release
__fput
Although pci_device_is_present() is slower than
pci_dev_is_disconnected(), it still takes only ~70 µs on a
ConnectX-5 (8 GT/s, x2) and becomes even faster as PCIe speed
and width increase.
Besides, devtlb_invalidation_with_pasid() is called only in the
paths below, which are far less frequent than memory map/unmap.
1. mm-struct release
2. {attach,release}_dev
3. set/remove PASID
4. dirty-tracking setup
The gain in system stability far outweighs the negligible cost
of using pci_device_is_present() instead of pci_dev_is_disconnected()
to decide when to skip ATS invalidation, especially under GDR
high-load conditions. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: SCO: fix race conditions in sco_sock_connect()
sco_sock_connect() checks sk_state and sk_type without holding
the socket lock. Two concurrent connect() syscalls on the same
socket can both pass the check and enter sco_connect(), leading
to use-after-free.
The buggy scenario involves three participants and was confirmed
with additional logging instrumentation:
Thread A (connect): HCI disconnect: Thread B (connect):
sco_sock_connect(sk) sco_sock_connect(sk)
sk_state==BT_OPEN sk_state==BT_OPEN
(pass, no lock) (pass, no lock)
sco_connect(sk): sco_connect(sk):
hci_dev_lock hci_dev_lock
hci_connect_sco <- blocked
-> hcon1
sco_conn_add->conn1
lock_sock(sk)
sco_chan_add:
conn1->sk = sk
sk->conn = conn1
sk_state=BT_CONNECT
release_sock
hci_dev_unlock
hci_dev_lock
sco_conn_del:
lock_sock(sk)
sco_chan_del:
sk->conn=NULL
conn1->sk=NULL
sk_state=
BT_CLOSED
SOCK_ZAPPED
release_sock
hci_dev_unlock
(unblocked)
hci_connect_sco
-> hcon2
sco_conn_add
-> conn2
lock_sock(sk)
sco_chan_add:
sk->conn=conn2
sk_state=
BT_CONNECT
// zombie sk!
release_sock
hci_dev_unlock
Thread B revives a BT_CLOSED + SOCK_ZAPPED socket back to
BT_CONNECT. Subsequent cleanup triggers double sock_put() and
use-after-free. Meanwhile conn1 is leaked as it was orphaned
when sco_conn_del() cleared the association.
Fix this by:
- Moving lock_sock() before the sk_state/sk_type checks in
sco_sock_connect() to serialize concurrent connect attempts
- Fixing the sk_type != SOCK_SEQPACKET check to actually
return the error instead of just assigning it
- Adding a state re-check in sco_connect() after lock_sock()
to catch state changes during the window between the locks
- Adding sco_pi(sk)->conn check in sco_chan_add() to prevent
double-attach of a socket to multiple connections
- Adding hci_conn_drop() on sco_chan_add failure to prevent
HCI connection leaks |
| Improper input validation in .NET Framework allows an unauthorized attacker to deny service over a network. |
| Sandboxie-Plus is an open source sandbox-based isolation software for Windows. In versions 1.17.2 and earlier, a Time-of-Check-to-Time-of-Use (TOCTOU) race condition exists during addon installation. When a user installs an addon through the SandMan interface, UpdUtil.exe is spawned as SYSTEM by SbieSvc but stages files in the user-writable %TEMP%\sandboxie-updater directory. After UpdUtil verifies file hashes against the signed addon manifest, install.bat extracts files.cab and executes config.exe from its contents. Between hash verification and extraction, an unprivileged user can replace files.cab with a crafted cabinet containing a malicious executable, which is then run as SYSTEM. No UAC prompt is required.
This issue has been fixed in version 1.17.3. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix folio isn't locked in softleaf_to_folio()
On arm64 server, we found folio that get from migration entry isn't locked
in softleaf_to_folio(). This issue triggers when mTHP splitting and
zap_nonpresent_ptes() races, and the root cause is lack of memory barrier
in softleaf_to_folio(). The race is as follows:
CPU0 CPU1
deferred_split_scan() zap_nonpresent_ptes()
lock folio
split_folio()
unmap_folio()
change ptes to migration entries
__split_folio_to_order() softleaf_to_folio()
set flags(including PG_locked) for tail pages folio = pfn_folio(softleaf_to_pfn(entry))
smp_wmb() VM_WARN_ON_ONCE(!folio_test_locked(folio))
prep_compound_page() for tail pages
In __split_folio_to_order(), smp_wmb() guarantees page flags of tail pages
are visible before the tail page becomes non-compound. smp_wmb() should
be paired with smp_rmb() in softleaf_to_folio(), which is missed. As a
result, if zap_nonpresent_ptes() accesses migration entry that stores tail
pfn, softleaf_to_folio() may see the updated compound_head of tail page
before page->flags.
This issue will trigger VM_WARN_ON_ONCE() in pfn_swap_entry_folio()
because of the race between folio split and zap_nonpresent_ptes()
leading to a folio incorrectly undergoing modification without a folio
lock being held.
This is a BUG_ON() before commit 93976a20345b ("mm: eliminate further
swapops predicates"), which in merged in v6.19-rc1.
To fix it, add missing smp_rmb() if the softleaf entry is migration entry
in softleaf_to_folio() and softleaf_to_page().
[[email protected]: update function name and comments] |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: close crash window in attr dabtree inactivation
When inactivating an inode with node-format extended attributes,
xfs_attr3_node_inactive() invalidates all child leaf/node blocks via
xfs_trans_binval(), but intentionally does not remove the corresponding
entries from their parent node blocks. The implicit assumption is that
xfs_attr_inactive() will truncate the entire attr fork to zero extents
afterwards, so log recovery will never reach the root node and follow
those stale pointers.
However, if a log shutdown occurs after the leaf/node block cancellations
commit but before the attr bmap truncation commits, this assumption
breaks. Recovery replays the attr bmap intact (the inode still has
attr fork extents), but suppresses replay of all cancelled leaf/node
blocks, maybe leaving them as stale data on disk. On the next mount,
xlog_recover_process_iunlinks() retries inactivation and attempts to
read the root node via the attr bmap. If the root node was not replayed,
reading the unreplayed root block triggers a metadata verification
failure immediately; if it was replayed, following its child pointers
to unreplayed child blocks triggers the same failure:
XFS (pmem0): Metadata corruption detected at
xfs_da3_node_read_verify+0x53/0x220, xfs_da3_node block 0x78
XFS (pmem0): Unmount and run xfs_repair
XFS (pmem0): First 128 bytes of corrupted metadata buffer:
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
XFS (pmem0): metadata I/O error in "xfs_da_read_buf+0x104/0x190" at daddr 0x78 len 8 error 117
Fix this in two places:
In xfs_attr3_node_inactive(), after calling xfs_trans_binval() on a
child block, immediately remove the entry that references it from the
parent node in the same transaction. This eliminates the window where
the parent holds a pointer to a cancelled block. Once all children are
removed, the now-empty root node is converted to a leaf block within the
same transaction. This node-to-leaf conversion is necessary for crash
safety. If the system shutdown after the empty node is written to the
log but before the second-phase bmap truncation commits, log recovery
will attempt to verify the root block on disk. xfs_da3_node_verify()
does not permit a node block with count == 0; such a block will fail
verification and trigger a metadata corruption shutdown. on the other
hand, leaf blocks are allowed to have this transient state.
In xfs_attr_inactive(), split the attr fork truncation into two explicit
phases. First, truncate all extents beyond the root block (the child
extents whose parent references have already been removed above).
Second, invalidate the root block and truncate the attr bmap to zero in
a single transaction. The two operations in the second phase must be
atomic: as long as the attr bmap has any non-zero length, recovery can
follow it to the root block, so the root block invalidation must commit
together with the bmap-to-zero truncation. |
